Fostex D2424 manual 100, Saving of WAV files, After selecting the track, press the EXECUTE/YES key

Model D2424 Reference Manual (Saving and Loading Song Data)

Saving of “WAV” files

A WAV file is saved by the following procedure. Before proceeding to save, make sure a DOS formatted disk in FAT 16 is set in the SCSI ID6 equipment. The following explains the procedures for using a backup disk after it had been formatted.

The E-IDE hard disk (or optional DVD-RAM drive) for backup can be used by the same procedures at saving in the DOS formatted disk.

1.The SETUP mode is entered by pressing the [SETUP] key.

2.Select “Save PGM?” (“?” blinks) with the [JOG] dial and press the [EXECUTE/YES] key.

5.Select "OFF" and press the [EXECUTE/YES] key.

The display will change to selecting the program for saving.

Flashing

SETUP SURE?

The currently setup content will flash in the display.

SETUP	Flashing
		OL
OL			BIT	24
0	0
3	3			FS
6	6
9	9			kHz
12	12			CLOCK
18	18
24	24			INT
30	30
42	42
∞		∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

3.Select the flashing “SCSI6” with the [JOG] dial and press the [EXECUTE/YES] key. (Select "IDE2" when saving in the E-IDE hard disk or optional DVD-RAM disk.)

After displaying "drive name", the display will change to "Bkup Mode?" for selecting the backup mode ("WAVE" will flashes).

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

4.Select the backup mode "WAVE" with the [JOG] dial and press the [EXECUTE/YES] key.

The display will change to "CB Export? OFF" ("OFF" flashes) and ON-OFF of the clip board export can be setup.

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Normally, when saving ABS 0-REC END data, proceed to the next step while the setup is OFF.

But, under the following condition, save is executed with the setup ON.

< Please remember! >

When clip board export is set to ON, save is to be executed only on data within a desired range.

In such a case, the desired range must be registered by the CLIPBOARD IN and CLIPBOARD OUT points previous to executing save. For explanation on registering of CLIPBOARD IN/OUT points, refer to [Registering of the locate point (=editing point) on page 54.

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

6.Select the desired program with the [JOG] dial and press the [EXECUTE/YES] key.

The display will change to selecting the track to be saved. In the initial state, "All Trk" will flashes.

Flashing

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

If the [JOG] dial is rotated at this stage, in addition to

"All Trk" (flashing), "01 01" (flashing)-"56 56" (flashing) can be selected. This function is used when specifying any desired track and saving it.

Flashing

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

For example, if tracks 5-24 must be saved, "05 05" is selected. Then proceed to the following.

7.After selecting the track, press the [EXECUTE/YES] key.

If "All Trk" or any desired track was selected, the display will change to the following.

When "All Trk" is selected:

The display will change to making a new WAV file on the disk and "SURE?" will flashes.

Flashing

SETUP SURE?

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

When the [JOG] dial is rotated, "Eject" can be selected. To eject the disk, select "Eject" and press the [EXECUTE/ YES] key.

100