Fostex D2424 124, Setting the foot switch function, Setting the stop function at the mark point

Model D2424 Reference Manual (Changing the Initial Setting <SETUP mode>)

Setting the foot switch function

1.While the recorder is stopped, press the [SETUP] key to enter SETUP mode.

2.Turn the [JOG] dial to select “Foot SW ?” (“?” flashes), then press the [EXECUTE/YES] key.

A flashing “?” will extinguish by pressing the [EXECUTE/ YES] key and the foot switch function information that was lit will being flashing. Initial setting, it will show “Punch IO”.

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

3.Select the desired function by rotating the [JOG] dial.

4.After selecting the function, press the [EXECUTE/

YES] key again.

The selected foot switch function will be registered and the Step-2 "?" will return to flashing.

5.Exit from the SETUP mode by pressing the [EXIT/ NO] key (or [STOP] button).

To cancel the operation, or to restore the setting obtained prior to the [EXECUTE/YES] key press, press the [STOP] button or the [EXIT/NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Setup of the stop function at the mark point (“Mark Stop MD?” menu)

At the “Setup of the stop function at the mark point” menu, this sets whether or not D2424 should automati- cally stop at the preset mark point (=locate point) during playback.

• Initial setting:	[Off]
• Option:	[OFF] or [On]

*This setting is shared by all Programs in the same disk.

*The settings cannot be saved and loaded as part of the song data.

*The settings are maintained after you turn off the power to the recorder.

Setting the stop function at the mark point

1.While the recorder is stopped, press the [SETUP] key to enter SETUP mode.

2.Turn the [JOG] dial to select “Mark Stop MD?” (“?” flashes), then press the [EXECUTE/YES] key.

3. Select "On" or "Off" with the [JOG] dial and press the [EXECUTE/YES] key again.

The selected stop function will be registered and the Step-2 "?" will return to flashing.

A flashing “?” will extinguish by pressing the [EXECUTE/ YES] key and the stop function at the mark point information that was lit will being flashing. Initial setting, it will show “Off”.

SETUP

OL			OL	BIT	24
0	0
3		3			FS
6			6
9		9			kHz
12		12			CLOCK
18		18
24		24			INT
30		30
42	42
∞			∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

4.Exit from the SETUP mode by pressing the [EXIT/ NO] key (or the [STOP] button).

To cancel the operation, or to restore the setting obtained prior to the [EXECUTE/YES] key press, press the [STOP] button or the [EXIT/NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.

124