Fostex D2424 Analog Input jack connector Phone, Remote Thru connector, Remote Input connector

Model D2424 Reference Manual (Names and Functions)

Rear panel section

1 2 3 4 5

ANALOGNALOGINPUTINPUTBALANCEB LANCE[ +4dBu[ +4dBu] / UNBALANCE] / UNB LANCE[ -10dBV[-10dBv] ]									ANALOGANALOGOUTPUTOUTPUTBALANCEBALANCE[ +4dBu[ +4dBu] /]UNBALANCE/ UNBALANCE[ -10dBv[-10dBV] ]
4		3	2	1	12	11	10	9	8	7	6	5	4	3	2	1
																	REMOTERS422
																REMOTE	100Ω	THRU
																	ON OFF
8		7	6	5	24	23	22	21	20	19	18	17	16	15	14	13
						WORDWORD
						INPUT	OUTPUT
					75Ω
					ON	OFF
																		AC-IN
			DATA				MIDIMIDI				SCSISCSI
	INPUT			OUTPUT		INPUT	OUTPUT	THRU							CAUTION
24 - 17	16 - 9	8 - 1	24 - 17	16 - 9	8 - 1
														AVIS:	RISQUE DE CHOC ELECTRIQUE
															NE PAS OUVRIR
														WARNING:
														TO REDUCE THE RISK OF FIRE OR ELECTRIC
														SHOCK, DO NOT EXPOSE THIS EQUIPMENT
														TO RAIN OR MOISTURE.

7 14 13 12 11 10 9 8 7 6

1.Analog Input jack (connector: PHONE)

External analog audio signals to the D2424 are input here. These are connected, for example, to external mixer's group out (BUSS OUT) connectors. As signals applied to [INPUT 1-8] are simultaneously sent to tracks 1-8, 9-16 and 17-24, tracks for recording must be selected via the [RECORD TRACK] select key.

5. REMOTE THRU connector

RS-422 control signal (SONY 9PIN PROTOCOL or Fostex System Exclusive Message) input from the [REMOTE INPUT] connector is output here.

This is connected to the second recorder REMOTE INPUT when controlling a multiple number of recorders.

<Note>

Analog input/output can be switched for balance/ unbalance via the SETUP mode. At initial setup, it is set for unbalance.

2.Analog Output jack (connector: PHONE)

Analog audio signals (Channels 1-24) from D2424 are output here. For example, this is connected to the external mixer [TAPE IN] connector.

<Note>

When using a current drive formatted to 96kHz 24 bits or 88.2kHz 24 bits, only [OUTPUT 1-8] will be functional.

3. REMOTE INPUT connector

External RS-422 control signal (SONY 9PIN PROTOCOL or Fostex System Exclusive Message) is input here to control this recorder.

4. REMOTE INPUT terminating switch

This REMOTE INPUT terminating switch (100Ω ) is switched ON for normal use of an inputted RS-422 control signal into the [REMOTE INPUT] connector. When controlling a multiple number of recorders, the last one only is switched ON; the others are switched OFF.

6. AC IN connector

The power cable packaged with this recorder is connected here.

<Note>

Always plug the power cable to the recorder before plugging the cable into the wall outlet.

7. Optional Panel

The additional installation panel for the optional Model 8345 (TC/SYNC card x1) or Model 8350 (AES/ EBU card x 1). Normally, it can be used with the panel remained installed.

•For functions at installation of the optional Model 8345, please refer to [References] on the last page of this manual.

<Note>

Installation of the option must be done by our Fostex Service Station. For details, please inquire at your nearest Fostex Service Station.

8. SCSI connector [SCSI]

(connector: half-pitch 50-pin)

Connect a backup SCSI device to SAVE/LOAD data. Up to one SCSI devices can be connected to the SCSI connector.

*Refer to page “91” for more details on SAVE/LOAD using a SCSI device.

18