Fostex D2424 manual 139, 13 42 channelchannel digital out ch.select command

Model D2424 Reference Manual (MIDI Implementation Chart/MMC List)

data length in the clipboard is less than 10ms, specifying the <repeat count> will be limited to "01."

Also, by specifying the <mmc track>, paste operation can be executed on other tracks in mono (one track unit) or stereo units (tracks 1-2, 3-4, 5-6, 7-8....).

Since time corresponding to length of the move clipped sound data is required to complete the move paste operation, D2424 will immediately reply with "32 4E (<edit message=02 (ac- tive)>)" after receiving the command.

Following completion of the move paste operation, "32 4E (<edit message = 01 (completed)>)" will be sent.

If paste cannot be executed due to improper figures of the previously registered auto punch in point, insufficient disc ca- pacity, no sound data is in the clipboard, etc., the correspond- ing <edit message> will be replied.

13 42 (<channel><channel>): digital out ch.select command

The source channel for digital out is selected.

Normally, the first <channel> shown will be the SPDIF L chan- nel data, and the second <channel> the SPDIF R channel out- put. (<00><00>) is the default setting. By FDMS-3 V3.0, any channel within "1 ~ 8" (or 9 ~ 16 or 17 ~ 24) can be selected.

13 42 (<channel=7F><channel=0>): Adat out select command

In a device which can be switched between SPDIF and Adat, if the first display is <channel=7F>, then Adat Out can be setup.

13 43(<program>): program change command

The command for PROGRAM CHANGE of D2424. The present program number can be changed to the figure indicated by <program>.

12 4F (<channel><channel>): track exchange command

When the D2424 receives this command, the track can be ex- change between the specified <channel><channel>. Especially, if the first <channel=00><channel=01>, then exchange by grouping will be executed between channel 1-8 and channel 17-24, and if the next byte <channel=00><channel=02>, then the exchange will be between channel 9-16 and channel 17-24. If it cannot be executed for some reason, an error mes- sage will be sent back.

13 3E: product new program command

When the D2424 receives this command, a new program is compiled and the current program is transferred to the new program. As compilation of the new program is comparatively short time, it is replied with "33 3E (<edit message=01 (com- pleted)>)" immediately upon completion of execution.

If it cannot be executed for some reason, an error message will be sent back.

13 3F: delete current program command

When the D2424 receives this command, the current program is deleted and succeeding programs moved up and renumberd. If the deleted program is the only tune existing in the track, a new program will be made automatically.

As this delete current program is executed in a comparatively short time, "33 3F (<edit message=01 (completed)>)" will be sent back immediately upon completing the execution.

If it cannot be executed for some reason, an error message will be sent back.

13 41 (<channel><channel>): digital in ch.select command

The audio signal input from SPDIF digital in to assigned to the destination track specified by <channel>. The first <channel> shown in the command is the SPDIF L channel input, and the second <channel> the R channel input. "<channel=0> <chan- nel =0>" indicates the normal analog input. In D2424, chan- nels 1 and 2 only can be selected for other than <channel=0>.

13 41 (<channel=7F><count><mmc track>): Adat in select com- mand

Channel = 7F indicates that it is Adat In. Normally, it will be "<count=0>" and all channels will be inputs from Adat In.

If <count=0><mmc track> is indicates, then only the tracks selected will be Adat In inputs. "<channel=0><channel=0>" indicates the normal analog input.

13 44 (<on/off>): click on/off command

The command for setting the metronome on/off of D2424. When ON is set, the metronome signal will be fed to the track 24 output of D2424.

13 46 (<on/off>): Bar/Beat Resolution ON/OFF command

The command for ON/OFF of the bar/beat resolution function of this equipments' current program.

13 47 (<midi sync>): Midi Sync Out command

The setup command for MIDI Sync Out mode of this equip- ments' current program.

13 48 (<MTC offset mode>): MTC offset mode command

The setup command for MTC offset mode of this equipment’s current program.

13 49 (<count=3> <on/off> <vari data>): Vari pitch command

13 49 (<count=1> <on/off>): Vari pitch command

The command for setting this equipments' vari pitch ON/OFF and pitch data.

Control of ON/OFF only is possible at <count=1> and both ON/ OFF and pitch data can be set at <count=3>.

14 01 (<signature map>): Signature set command

The command for setting the meter of this equipment. If a new data is registered at the bar position where a data exists, the former data will be written over. When this command is re- ceived, this equipment will reply with "34 01 (<edit message>)." Upon completing the registeration, <edit message> will reply with "01 (completed)," or with "10 (over value error)" if registeration is attempted at a non-existing point or an errone- ous figure is used.

14 02 (<tempo set map>): Tempo set command

The command for tempo set of this equipment. If a new data is registered in a bar/meter where data already exists, the former data will be written over. When this command is received, this equipment will reply with "34 02 (<edit message>)." Upon completing the registeration, <edit message> will reply with "01 (completed)," or with "10 (over value error)" if registeration is attempted at a non-existing point or an erroneous figure is used.

14 03 : Tempo map all erase command

When this command is received, this equipment will erase all meter and tempo data in the current program and thus return

139