Fostex D2424 Record button Record, Edit key EDIT/TC Ready, Auto Punch Mode On/Off key Auto Punch

Model D2424 Reference Manual (Names and Functions)

*2 Locate ABS 0:

The recorder will locate the top of the selected Program (ABS TIME: 00m: 00s: 00f).

*3 Locate REC END:

The recorder will locate the end of the recorded data on the Program (ABS REC END).

These operations can be executed only on real tracks.

*Refer to page “24” of the “Before Starting” section for more information about ABS 0 and ABS END.

*Refer to page “42” for more information about Punch In/Out recording using the foot switch.

*Refer to page "67" on details for "Clip board play."

*Refer to page "54" on details for "LOCATE 0" and "LOCATE REC END."

29. Record button [RECORD]

Pressing only this button places the readied tracks into input monitoring status. Pressing this button again will reset the tracks to playback monitoring. (The RECORD LED will blink when the readied tracks are in input monitoring status.)

Pressing the [PLAY] button while holding down this button will place the readied tracks into recording. At this time, the PLAY LED and RECORD LED will light, and the readied track indication will be light steadily (instead of blinking).

*Refer to page “28” of the “Before Starting” section for more information about input monitoring and reproduce monitoring.

28. Edit key [EDIT/TC READY]

Pressing this key enters the recorder to the menu select mode for editing tracks. Press this key repeatedly or turn the [JOG] dial to select menu.

Edit menus appear in the following order. To execute a desired menu, select the menu, then press the [EXECUTE/YES] key. To exit the selection mode, press the [EXIT/NO] key.

If the optional Model 8345 TC/SYNC card is installed, you can enter the TC READY mode for recording time code by pressing this key while pressing on the [SHIFT] key.

Copy Clip?

Move Clip?

Copy Paste? (Move Paste?(*1))

Erase?

Track Exchange?

PGM Duplicate?(*2)

(*1): After you execute copy clip, “Copy Paste” appears. After you execute move clip, “Move Paste” appears.

(*2): The program duplicate display will appear only if the current drive was set to ON for the "Multiple Undo Function" when formatting. If the current drive is set to OFF, the program duplicate display will not appear even if the [EDIT] key is pressed.

*Refer to page “66” for more information about “Copy Clip,” “Move Clip,” “Copy Paste,” “Erase,” and “Track Exchange.”

*Refer to page “36” for more information about program duplicate function.

<Note>

This key is enabled only when the recorder is stopped.

30. Auto Punch Mode On/Off key [AUTO PUNCH]

Switch this key ON for auto punch in/out.

When you press this key while a correct value is stored to the [AUTO PUNCH IN] key and the [AUTO PUNCH OUT] key, both the REHEARSAL LED and TAKE LED will blink, indicating that Auto Punch mode is on. (If a correct value is not stored, pressing the [AUTO PUNCH] key will not turn the parameter ON, and the message “Void Out Point!” will appear.)

Pressing the [PLAY] button under this condition will put the recorder into “Rehearsal mode” for Auto Punch In/Out recording. Pressing the [PLAY] button and [RECORD] button simultaneously will put the recorder into “Take mode.”

There are five combinations of the REHEARSAL LED and TAKE LED that indicate the status of the recorder regarding auto punch recording:

Auto Punch mode OFF

Both REHEARSAL LED and TALE LED are off.

Auto Punch mode ON

Both REHEARSAL LED and TALE LED are blinking.

Auto Punch TAKE mode

Only the TAKE LED (red) is lit.

Auto Punch REHEARSAL mode

Only the REHEARSAL LED (green) is lit.

Rehearsal mode entered by means of MMC or foot switch

Only the REHEARSAL LED (green) is blinking.

16