Fostex D2424 manual 108, Modifying or deleting stored time signatures

Model D2424 Reference Manual (Changing the Initial Settings <SETUP mode>)

Modifying (or deleting) stored time signatures

1.Repeat steps 1-3 described in the “Storing a time signature” section.

2.Turn the [SHUTTLE] dial so that the flashing cursor is on the time signature value.

3.Use the [JOG] dial to enter a new value.

Entering “-/-” deletes the existing data. Note that you cannot enter “-/-” for measure 001.

4.Press the [EXECUTE/YES] key.

5.Press the [EXIT/NO] key (or [STOP] button).

<Caution>

If modifying or deleting the stored time signature causes the bar/beat setting for the tempo specified in the “Setting a tempo” menu to disappear, the tempo setting will also be automatically erased.

To cancel the setting operation, or to exit SETUP mode after storing data, press the [STOP] button or the [EXIT/ NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode.

Clearing all time signature and tempo settings

<Caution>

Using this function will erase not only the time signature setting but also the tempo data specified in the “Setting a tempo” menu described in the next section.

1.Repeat steps 1-3 described in the “Storing a time signature” section.

2.While the measure number is flashing, turn the [JOG] dial counter-clockwise to select “All Clear?.”

When “All Clear ?” appears, “SURE ?” flashes, and you can clear the time signature and tempo data in the next step.

Flashing

SETUPSURE?

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

3.Press the [EXECUTE/YES] key.

The stored time signature and tempo data in its entirety are cleared, and the initial settings are restored.

4.Press the [EXIT/NO] key (or [STOP] button).

To cancel the All Clear operation, press the [STOP] button or the [EXIT/NO] key now. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode.

Changing the bar at ABS “0” of the time base

Bar in -002bar/1beat/00clk, which indicates the head figure of the disk in the time base BAR/BEAT/CLK, can be changed. Although the initial figure is -002bar, this can be set within the range of -009bar ~ -002bar.

1.Repeat steps 1-2 described in the “Storing a time signature” section.

2.Turn the [JOG] dial counter-clockwise to select “-002 bar Offset.”

3.Press the [EXECUTE/YES] key.

“2” in “-002bar” will flash and the bar figure can be changed with the [JOG] dial (Numbers that can be input are 2~9.)

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

4.Use the [JOG] dial to enter a new value.

5.Press the [EXECUTE/YES] key.

6.Press the [EXIT/NO] key (or [STOP] button).

To cancel the setting operation, or to exit SETUP mode after storing data, press the [STOP] button or the [EXIT/ NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode.

108