Model D2424 Reference Manual (Changing the Initial Settings <SETUP mode>)

Recording enabled/disabled

1.While the recorder is stopped, press the [SETUP] key to enter SETUP mode.

2.Turn the [JOG] dial to select “Rec Protect ?” (“?” flashes), then press the [EXECUTE/YES] key.

The current setting appears on the display.

Pressing the [EXECUTE/YES] key turns off the flashing “?” character, and the recording enabled/disabled indicator flashes. With the initial setting, “Off” flashes as shown below.

SETUP

OL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL

BIT

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

0

 

 

 

 

 

3

 

 

 

3

 

FS

 

 

 

6

 

 

 

 

 

6

 

 

 

 

 

 

9

 

 

 

9

 

kHz

 

 

 

12

 

 

 

12

 

CLOCK

 

 

 

18

 

 

 

18

 

 

 

 

24

 

 

 

24

 

INT

 

 

 

30

 

 

 

30

 

 

 

 

 

 

42

 

 

 

 

42

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Flashing

SETUP

OL

OL

BIT

24

0

0

 

 

3

3

 

FS

6

6

 

9

9

 

kHz

12

12

 

CLOCK

18

18

 

24

24

 

INT

30

30

 

 

42

42

 

 

 

 

3.Use the [JOG] dial to enable or disable recording.

Rotating the [JOG] dial clockwise and counter-clockwise will flash “On” and “Off” alternately.

Selecting “Off” enables recording; you can record, paste, and erase data.

Selecting “On” disables recording; and you cannot record, paste, or erase data.

<Note>

When recording is disabled (On) and you try to record, paste, or erase data, the recorder displays “Protected” for a second, indicating that you cannot perform the operation. To perform the operation, you need to enable recording (Off).

4.Press the [EXECUTE/YES] key.

To cancel the operation, or to restore the setting obtained prior to the [EXECUTE/YES] key press, press the [STOP] button or the [EXIT/NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Setting digital input (“D. in ?” menu)

In the “Setting a digital input” menu, the signal to be input to the DATA INPUT connector of the recorder can be set for either digital signals (adat digital signal or S/P DIF digital signal) or analog signals, and also setup of the digital in clock (synchronous or asynchronous).

By using this function, signals from external digital equipment (CD, MD, DAT, adat digital mixer) can be digitally recorded.

When selecting the clock, there are the Async and Sync modes; either should be selected depending on the application. If it is set to “Async mode,” the later explained [Clock Sel?] (Setting the operating clock) should be setup in accordance to the application.

• Initial setting:

[Analog]

Assignable digital signal/setting digital in-clock: [adat: Async] (adat digital signal/Asynchronous mode) [adat: Sync] (adat digital signal/Synchronous mode) [SPDIF: Async] (S/P DIF digital signal/Asynchronous mode)

[SPDIF: Sync] (S/P DIF digital signal/Synchronous mode) [Analog] (not assigned digital signal)

*This setting is shared by all Programs in the same disk.

*The settings cannot be saved and loaded as part of the song data.

*The settings are maintained after you turn off the power to the recorder.

<Function of the DATA INPUT connectors>

<Setup for analog signals>

If the digital input is set up for Analog (Initial setting), digital signals cannot be input at DATA INPUT 1-8, 9-16 and 17-24 of the D2424.

<Setup for S/P DIF digital signals>

If the digital input is set up for S/P DIF (Async or Sync), only DATA INPUT 1-8 can be used.

S/P DIF digital signals input to DATA INPUT 1-8 will be assigned and recorded in tracks 1 and 2 of D2424.

<Setup for adat digital signals>

If the digital input is set up for adat (Async or Sync), all DATA INPUT connectors can be used.

Adat digital signals input to DATA INPUT 1-8 will be assigned and recorded in tracks 1-8; the signals to INPUT 9-16 in tracks 9-16; and the signals to INPUT 17-24 in tracks 17-24.

117

Page 117
Image 117
Fostex D2424 Setting digital input D. in ? menu, 117, Recording enabled/disabled, Function of the Data Input connectors