Model D2424 Reference Manual (Changing the Initial Settings <SETUP mode>)

3. Use the [JOG] dial to set the desired MIDI device ID number.

Turning the [JOG] dial clockwise increments the value, and turning it counter-clockwise decrements the value.

4. Press the [EXECUTE/YES] key.

The MIDI device ID number is stored, and “?” flashes.

To cancel the operation, or to restore the setting obtained prior to the [EXECUTE/YES] key press, press the [STOP] button or the [EXIT/NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.

Setting the Operating Clock (“Clock Sel ?” menu)

The “Setting the Operating Clock” menu is used to setup the operating clock of the recorder.

If digital input is set to asynchronous mode of “adat: Async” or “SPDIF: Async” in the previous “D. in?” (Digital input setting), whether this recorder is to operated by its internal clock or synchronized to the word clock signal from the external digital equipment should be selected when recording in digital from external digital equipment (DAT, adat, CD, MD, etc.). The initial setting is set to synchronize to the internal clock.

The setup item [Video] is effective if an optional Model 8345 TC/SYNC card is installed. For details, refer to the “APPENDIX.”

• Initial setting:

[Int.]

• Option:

[Int.] (Internal clock)

 

[Auto]

 

[Word]

 

[Video] (Tis item will be effective if the optional Model 8345 TC/SYNC card is

 

installed in this recorder.)

*This setting is shared by all Programs in the same disk.

*The settings cannot be saved and loaded as part of the song data.

*The settings are maintained after you turn off the power to the recorder.

Setting the operating clock

1.While the recorder is stopped, press the [SETUP] key to enter SETUP mode.

2.Turn the [JOG] dial to select “Clock Sel ?” (“?” flashes), then press the [EXECUTE/YES] key.

A flashing “?” will extinguish by pressing the [EXECUTE/ YES] key and the operating clock information that was lit will being flashing. Initial setting, it will show “Int.

SETUP

OL

OL

BIT

24

0

0

 

 

3

3

 

FS

6

6

 

9

9

 

kHz

12

12

 

CLOCK

18

18

 

24

24

 

INT

30

30

 

 

42

42

 

 

 

 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Flashing

SETUP

OL

OL

BIT

24

0

0

 

 

3

3

 

FS

6

6

 

9

9

 

kHz

12

12

 

CLOCK

18

18

 

24

24

 

INT

30

30

 

 

42

42

 

 

 

 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

3.With the [JOG] dial, select the operating clock.

If “Int.” (initial setting) is selected, the recorder will operate using the internal clock.

If “Auto” is selected, the recorder will sync to an external digital signal.

If “Word” is selected, the recorder will sync to an external word clock signal.

4.Press the [EXECUTE/YES] key.

The selected operating clock will register and “?” in step- 2 above, will flashes.

Refer to the chart of next page in regards to “Digital input setting” and “Operating clock setting.”

To cancel the operation, or to restore the setting obtained prior to the [EXECUTE/YES] key press, press the [STOP] button or the [EXIT/NO] key. Each time you press one of these keys, the recorder returns to the previous hierarchy level of the menu, and finally exits SETUP mode and displays the previous Time Base.

121

Page 121
Image 121
Fostex D2424 manual Setting the Operating Clock Clock Sel ? menu, 121, Setting the operating clock