SERVICE AND ADJUSTMENTS

TO REPLACE BELTS

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

BEFORE REPLACING BELTS

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rotator head to mounting bracket to allow chute rotator head to be raised and discharge chute to be removed from snow thrower. See Fig. 19.

CHUTE ROTATOR HEAD

LOCKNUT

MOUNTING

BRACKET

FIG. 19

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

AUGER BELT REPLACEMENT (See Fig. 20)

TO REMOVE AUGER BELT

1.Remove upper 5/16” bolts and lower 1/4” bolts from both sides of the frame assembly. Do not discard bolts.

2.Loosen but DO NOT REMOVE lower 5/16” bolts on both sides of the frame assembly.

3.Remove the auger belt from the engine pulley.

4.Tip the back section down. The front section will tip forward at the same time, as the bottom bolt acts as a hinge between the front and back sections. Use a block under the hinge point to secure the snow thrower in the tipped position as shown.

5.Move auger belt tensioner arm and remove auger belt from around the arm.

TO INSTALL AUGER BELT

1.Move belt tensioner arm and place auger belt around and inside groove of the auger pulley.

NOTE: Ensure the belt is not pinched between the frame and auger housing as you bring the unit back together.

2.Remove block from under the snow thrower. Lift the handles to tip the back section up. The front section will tip back and pivot to rejoin the back section.

3.Ensure belt is routed inside auger pulley groove properly.

4.Install the previously removed and loosened 5/16” bolts, and tighten securely. (8-12 Ft. Lbs. / 11-16 Nm).

Install the previously removed 1/4” bolts (X2), and tighten securely. (4-6 Ft. Lbs. / 5-8 Nm).

5.Install auger belt onto engine pulley. Ensure belt is routed correctly around idler pulley and seated properly in engine pulley groove.

6.Operate all controls to ensure belts are installed properly and that all components are moving correctly.

Continue with “AFTER REPLACING BELTS” instructions.

ENGINE PULLEY

 

 

AUGER

 

 

 

 

 

 

 

 

BELT

AUGER BELT

 

 

 

 

TENSIONER ARM

 

 

 

HANDLE

 

 

 

 

FRAME

UPPER

 

LOWER

 

ASSEMBLY

5/16"

LOWER

1/4" BOLT

AUGER

 

BOLT

5/16" BOLT

 

PULLEY

FIG. 20

16

Page 16
Image 16
Husqvarna ST 224 warranty To Replace Belts, Before Replacing Belts, Auger Belt Replacement See Fig, To Remove Auger Belt

ST 224 specifications

The Husqvarna ST 224 is a powerful, versatile snowblower designed to tackle even the harshest winter conditions. Built for residential use, this reliable two-stage snow thrower excels in clearing medium to large-sized driveways, sidewalks, and parking areas, efficiently managing snow up to 12 inches deep.

One of the standout features of the ST 224 is its robust engine. It is powered by a reliable 223cc Husqvarna engine, which delivers impressive performance and durability. The engine’s efficient design allows for easy starting, even in frigid temperatures. With a maximum throwing distance of approximately 33 feet, this snowblower can rapidly discharge snow, making quick work of winter's toughest tasks.

The snowblower is equipped with a 24-inch wide clearing width and a 23-inch intake height, allowing it to accommodate heavy snowfall with ease. The auger system efficiently collects snow, while the impeller system provides powerful throwing capabilities. This combination ensures that users can clear snow quickly and efficiently.

Husqvarna has incorporated several user-friendly features into the ST 224, making it easy to operate. The adjustable skid shoes allow users to customize the height of the machine relative to the surface being cleared, preventing damage to driveways or sidewalks. The remote chute rotation and deflector adjustment enable users to aim the snow where they want it to go with minimal effort.

When it comes to maneuverability, the Husqvarna ST 224 shines. It features large, deep-tread wheels that provide excellent traction, even in icy conditions. This mobility is further enhanced by the lightweight construction of the snowblower, making it easy to handle and operate.

The snowblower's durable construction ensures longevity, even during demanding use. The steel frame and housing provide the necessary robustness, while the corrosion-resistant materials ensure that the machine can withstand the wear and tear of winter weather.

Overall, the Husqvarna ST 224 combines power, efficiency, and user-friendly features. It’s an ideal choice for homeowners who need a reliable snowblower that can handle heavy snowfall, offering exceptional performance and ease of use throughout the winter months. With its impressive features and technologies, the Husqvarna ST 224 stands out as a top choice for residential snow removal.