Manuals / Omega / Personal Care / Thermometer

Omega DP119-RTD manual 4. Installation Information

Models: DP119-RTD

1 36

Download 36 pages 21.74 Kb

Page 18

Figure 3-4. Installation Information

			PANEL THICKNESS
			0.25 [6.4]			MAX
			0.03 [0.8]			MIN
1/8 DIN PANEL CUTOUT
	R 0.06

			1.772		+0.024/-.000
[1.5]			1.772		+0.024/-.000
	4PLCS		[45.0		+0.61/-0.00]
3.622 +0.032/-.000
3.622 +0.032/-.000
		[92.00	+0.81/-0.00]

	SCREWS
	METER
	BEZEL
LENS	BACKPLATE
	BACKPLATE
	PANEL WITH
	1/8 DIN CUTOUT

Figure 3-4. Installation Information

11

Image 18

Omega DP119-RTD manual 4. Installation Information

Contents

Thermometer DP119-RTDMiniature Panel UserÕs GuideServicing North America OMEGAnetSM On-Line ServiceInternet e-mail info@omega.com For immediate technical or application assistanceTABLE OF CONTENTS SECTIONPAGE Refer to Table 1-1 for the complete listing of models available MODELS AVAILABLE RESOLUTIONPower Options Available MODELPOWER RTD MODELS AVAILABLEMODEL Other Models AvailableRESOLUTION TYPENOTES, WARNINGS and CAUTIONS SECTION 1 INTRODUCTION 1.1 UNPACKING QTY DESCRIPTIONcarton in the event reshipment is necessary 1.2 SAFETY CONSIDERATIONS Unpacking & InspectionEMC Considerations Removable Screw-Clamp Cable Connector Display Hold Capability SECTION 2 ABOUT THE METER 2.1 Front of the MeterFeatures Figure 2-1 shows the panel thermometerConnector 2.3 Connector DescriptionConnector Description Signal LoSECTION 3 GETTING STARTED 3.1 Main Board Power Jumpers REMOVE INSTALLAC VOLTAGE Voltage Jumper Pin Settings3.2 Changing the Meter Parameters Refer to Table 1-1, for complete models preface section TABLE 3-2 2-, 3-, 4-Wire, Upscale, Downscale ConfigurationThe following tables summarizes what parameters you can change TABLE 3-1 Range ParametersSENSOR BREAK PROTECTION Section 3.3 Installation and Panel Mounting Figure 3-4. Installation Information 4-Wire RTD 2-Wire RTD3-Wire RTD 3.4 Sensor Input ConnectionsWire colors are for OMEGA RTD wiring only 3.4 Sensor Input Connections ContinuedNote Refer to Table 3-1 and Table 3-2 for internal jumper settings Figure 3-6. 2-Wire RTD Wiring3.5 Analog Output Connections 3.6 Display Hold Connections 3.7 Main Power Connections DC WIRING 3.8 Disassembly/Assembly PULL TAB HERE PC BOARD PUSH HERE SECTION 4 OPERATION AND CALIBRATION 4.1 EQUIPMENT REQUIRED4.2 CALIBRATION PROCEDURE Figure 4-1. 2-Wire ConfigurationFigure 4-2. 3-Wire Configuration RESISTANCE CALIBRATION VALUES WHEN YOU ARE USING RESISTANCE SOURCEADJUST METERSECTION 5 SPECIFICATIONS DISPLAY MECHANICAL DIMENSIONSPOWER ENVIRONMENTAL3.78 96.0 TOP VIEW Figure 5-1 Dimensions1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW 0.76 3.76 95.5 4.32 109.7 MAXSECTION 6 GLOSSARY Page USAWARRANTY/DISCLAIMER RETURN REQUESTS / INQUIRIESPRESSURE, STRAIN AND FORCE TEMPERATUREOMEGAÉOf Course FLOW/LEVEL