Manuals / Omega / Personal Care / Thermometer

Omega DP119-RTD manual Pull Tab Here Pc Board Push Here

Models: DP119-RTD

1 36

Download 36 pages 21.74 Kb

Page 26

PULL TAB HERE

PULL TAB HERE

PC BOARD

PUSH HERE

1	2	3	1	2	3	1	2	3	4
	P1			P2			P3

Figure 3-13. Removing the PC Board from the Case

When re-installing the printed circuit board:

1.Hold the case (with the two mounting holes facing upwards and to the right side of the case) in the left hand.

2.Hold the printed circuit board with the components showing (soldered side down) in the right hand.

3.Slip the component board into the case and slide in as far as it will go. You will also have to release the tab at the rear on the other side of the case (turn case over) to allow the board to fit all the way inside the case.

4.Go through steps 3 thru 5 in Section 3.3 in order to re-install the backplate and screws, and also install the lens.

19

Image 26

Omega DP119-RTD manual Pull Tab Here Pc Board Push Here

Contents

Thermometer DP119-RTDMiniature Panel UserÕs GuideServicing North America OMEGAnetSM On-Line ServiceInternet e-mail info@omega.com For immediate technical or application assistancePAGE TABLE OF CONTENTSSECTION Refer to Table 1-1 for the complete listing of models available MODELS AVAILABLE RESOLUTIONPower Options Available MODELPOWER RTD MODELS AVAILABLEMODEL Other Models AvailableRESOLUTION TYPENOTES, WARNINGS and CAUTIONS carton in the event reshipment is necessary SECTION 1 INTRODUCTION 1.1 UNPACKINGQTY DESCRIPTION EMC Considerations 1.2 SAFETY CONSIDERATIONSUnpacking & Inspection Removable Screw-Clamp Cable Connector Display Hold Capability SECTION 2 ABOUT THE METER 2.1 Front of the MeterFeatures Figure 2-1 shows the panel thermometerConnector 2.3 Connector DescriptionConnector Description Signal LoSECTION 3 GETTING STARTED 3.1 Main Board Power Jumpers REMOVE INSTALLAC VOLTAGE Voltage Jumper Pin Settings3.2 Changing the Meter Parameters Refer to Table 1-1, for complete models preface section TABLE 3-2 2-, 3-, 4-Wire, Upscale, Downscale ConfigurationThe following tables summarizes what parameters you can change TABLE 3-1 Range ParametersSENSOR BREAK PROTECTION Section 3.3 Installation and Panel Mounting Figure 3-4. Installation Information 4-Wire RTD 2-Wire RTD3-Wire RTD 3.4 Sensor Input ConnectionsWire colors are for OMEGA RTD wiring only 3.4 Sensor Input Connections ContinuedNote Refer to Table 3-1 and Table 3-2 for internal jumper settings Figure 3-6. 2-Wire RTD Wiring3.5 Analog Output Connections 3.6 Display Hold Connections 3.7 Main Power Connections DC WIRING 3.8 Disassembly/Assembly PULL TAB HERE PC BOARD PUSH HERE SECTION 4 OPERATION AND CALIBRATION 4.1 EQUIPMENT REQUIREDFigure 4-2. 3-Wire Configuration 4.2 CALIBRATION PROCEDUREFigure 4-1. 2-Wire Configuration RESISTANCE CALIBRATION VALUES WHEN YOU ARE USING RESISTANCE SOURCEADJUST METERSECTION 5 SPECIFICATIONS DISPLAY MECHANICAL DIMENSIONSPOWER ENVIRONMENTAL3.78 96.0 TOP VIEW Figure 5-1 Dimensions1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW 0.76 3.76 95.5 4.32 109.7 MAXSECTION 6 GLOSSARY Page USAWARRANTY/DISCLAIMER RETURN REQUESTS / INQUIRIESPRESSURE, STRAIN AND FORCE OMEGAÉOf CourseTEMPERATURE FLOW/LEVEL