Manuals / Omega / Personal Care / Thermometer

Omega DP119-RTD 1 Dimensions, 1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW, 3.78 96.0 TOP VIEW, 0.25

Models: DP119-RTD

1 36

Download 36 pages 21.74 Kb

Page 32

1.89

1.89

[48.0]

BEZEL

BACKPLATE

CASE

SIDE VIEW

PANEL CUTOUT

3.78

[96.0]

TOP VIEW

			PANEL THICKNESS
			0.25 [6.4]		MAX
			0.03 [0.8]		MIN
	R 0.06

			1.772 +0.024/-.000
	[1.5]		1.772 +0.024/-.000
	4PLCS		[45.01 +0.61/-0.00]
	3.622 +0.032/-.000
	3.622 +0.032/-.000
		[92.00	+0.81/-0.00]

1/8 DIN

0.76 [19.3]

3.76

[95.5]

4.32

[109.7]

MAX

Figure 5-1 Dimensions

25

Image 32

Omega DP119-RTD 1 Dimensions, 1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW, 3.78 96.0 TOP VIEW, 0.76 3.76 95.5 4.32 109.7 MAX

Contents

DP119-RTD Miniature PanelThermometer UserÕs GuideOMEGAnetSM On-Line Service Internet e-mail info@omega.comServicing North America For immediate technical or application assistancePAGE TABLE OF CONTENTSSECTION Refer to Table 1-1 for the complete listing of models available RESOLUTION Power Options Available MODELPOWERMODELS AVAILABLE RTD MODELS AVAILABLEOther Models Available RESOLUTIONMODEL TYPENOTES, WARNINGS and CAUTIONS carton in the event reshipment is necessary SECTION 1 INTRODUCTION 1.1 UNPACKINGQTY DESCRIPTION EMC Considerations 1.2 SAFETY CONSIDERATIONSUnpacking & Inspection SECTION 2 ABOUT THE METER 2.1 Front of the Meter FeaturesRemovable Screw-Clamp Cable Connector Display Hold Capability Figure 2-1 shows the panel thermometer2.3 Connector Description Connector DescriptionConnector Signal LoSECTION 3 GETTING STARTED 3.1 Main Board Power Jumpers INSTALL AC VOLTAGEREMOVE Voltage Jumper Pin Settings3.2 Changing the Meter Parameters TABLE 3-2 2-, 3-, 4-Wire, Upscale, Downscale Configuration The following tables summarizes what parameters you can changeRefer to Table 1-1, for complete models preface section TABLE 3-1 Range ParametersSENSOR BREAK PROTECTION Section 3.3 Installation and Panel Mounting Figure 3-4. Installation Information 2-Wire RTD 3-Wire RTD4-Wire RTD 3.4 Sensor Input Connections3.4 Sensor Input Connections Continued Note Refer to Table 3-1 and Table 3-2 for internal jumper settingsWire colors are for OMEGA RTD wiring only Figure 3-6. 2-Wire RTD Wiring3.5 Analog Output Connections 3.6 Display Hold Connections 3.7 Main Power Connections DC WIRING 3.8 Disassembly/Assembly PULL TAB HERE PC BOARD PUSH HERE SECTION 4 OPERATION AND CALIBRATION 4.1 EQUIPMENT REQUIREDFigure 4-2. 3-Wire Configuration 4.2 CALIBRATION PROCEDUREFigure 4-1. 2-Wire Configuration CALIBRATION VALUES WHEN YOU ARE USING RESISTANCE SOURCE ADJUSTRESISTANCE METERSECTION 5 SPECIFICATIONS MECHANICAL DIMENSIONS POWERDISPLAY ENVIRONMENTALFigure 5-1 Dimensions 1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW3.78 96.0 TOP VIEW 0.76 3.76 95.5 4.32 109.7 MAXSECTION 6 GLOSSARY Page USAWARRANTY/DISCLAIMER RETURN REQUESTS / INQUIRIESTEMPERATURE OMEGAÉOf CoursePRESSURE, STRAIN AND FORCE FLOW/LEVEL