Manuals / Omega / Personal Care / Thermometer

Omega DP119-RTD manual 3 Installation and Panel Mounting

Models: DP119-RTD

1 36

Download 36 pages 21.74 Kb

Page 17

Section 3.3 Installation and Panel Mounting

Figure 3-4shows the panel cutout dimensions, the dimensions for the panel thickness, and the backplate for mounting the unit in a panel. Connections will be done after mounting the unit.

1.Remove the 2 phillips screws from behind the display (you don't have to go inside the meter) holding the rectangular backplate to the meter. Remove the backplate and set aside.

2.Cut or punch a hole in the panel where you want the meter to go. The panel can be as thick as 0.25" (6.4mm) to as thin as 0.03" (0.8mm).

3.Insert the meter into the panel cutout.

4.From the rear of the panel, slide the backplate over the case (smooth side out).

5.Install the 2 phillips screws to secure the meter in 1/8 DIN mount. Center the meter in hole prior to tightening screws.

10

Image 17

Omega DP119-RTD manual 3 Installation and Panel Mounting

Contents

Miniature Panel DP119-RTDThermometer UserÕs GuideInternet e-mail info@omega.com OMEGAnetSM On-Line ServiceServicing North America For immediate technical or application assistancePAGE TABLE OF CONTENTSSECTION Refer to Table 1-1 for the complete listing of models available Power Options Available MODELPOWER RESOLUTIONMODELS AVAILABLE RTD MODELS AVAILABLERESOLUTION Other Models AvailableMODEL TYPENOTES, WARNINGS and CAUTIONS carton in the event reshipment is necessary SECTION 1 INTRODUCTION 1.1 UNPACKINGQTY DESCRIPTION EMC Considerations 1.2 SAFETY CONSIDERATIONSUnpacking & Inspection Features SECTION 2 ABOUT THE METER 2.1 Front of the MeterRemovable Screw-Clamp Cable Connector Display Hold Capability Figure 2-1 shows the panel thermometerConnector Description 2.3 Connector DescriptionConnector Signal LoSECTION 3 GETTING STARTED 3.1 Main Board Power Jumpers AC VOLTAGE INSTALLREMOVE Voltage Jumper Pin Settings3.2 Changing the Meter Parameters The following tables summarizes what parameters you can change TABLE 3-2 2-, 3-, 4-Wire, Upscale, Downscale ConfigurationRefer to Table 1-1, for complete models preface section TABLE 3-1 Range ParametersSENSOR BREAK PROTECTION Section 3.3 Installation and Panel Mounting Figure 3-4. Installation Information 3-Wire RTD 2-Wire RTD4-Wire RTD 3.4 Sensor Input ConnectionsNote Refer to Table 3-1 and Table 3-2 for internal jumper settings 3.4 Sensor Input Connections ContinuedWire colors are for OMEGA RTD wiring only Figure 3-6. 2-Wire RTD Wiring3.5 Analog Output Connections 3.6 Display Hold Connections 3.7 Main Power Connections DC WIRING 3.8 Disassembly/Assembly PULL TAB HERE PC BOARD PUSH HERE 4.1 EQUIPMENT REQUIRED SECTION 4 OPERATION AND CALIBRATIONFigure 4-2. 3-Wire Configuration 4.2 CALIBRATION PROCEDUREFigure 4-1. 2-Wire Configuration ADJUST CALIBRATION VALUES WHEN YOU ARE USING RESISTANCE SOURCERESISTANCE METERSECTION 5 SPECIFICATIONS POWER MECHANICAL DIMENSIONSDISPLAY ENVIRONMENTAL1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW Figure 5-1 Dimensions3.78 96.0 TOP VIEW 0.76 3.76 95.5 4.32 109.7 MAXSECTION 6 GLOSSARY Page RETURN REQUESTS / INQUIRIES USAWARRANTY/DISCLAIMEROMEGAÉOf Course TEMPERATUREPRESSURE, STRAIN AND FORCE FLOW/LEVEL