Manuals / Omega / Personal Care / Thermometer

Omega DP119-RTD ABOUT THE METER 2.1 Front of the Meter, 1 shows the panel thermometer, Features

Models: DP119-RTD

1 36

Download 36 pages 21.74 Kb

Page 10

SECTION 2 ABOUT THE METER

SECTION 2 ABOUT THE METER

2.1Front of the Meter

Figure 2-1 shows the panel thermometer.

Figure 2-1. Panel Thermometer

Features:

Display:3 1/2 Digit, 7-Segment Red or Green LED Full-size:14.2 mm (0.56") LED Display

Analog Output Standard

1/8 DIN Standard Panel Cutout

Removable Screw-Clamp Cable Connector

Display Hold Capability

3

Image 10

Omega DP119-RTD ABOUT THE METER 2.1 Front of the Meter, 1 shows the panel thermometer, Features, 1. Panel Thermometer

Contents

Thermometer DP119-RTDMiniature Panel UserÕs GuideServicing North America OMEGAnetSM On-Line ServiceInternet e-mail info@omega.com For immediate technical or application assistanceSECTION TABLE OF CONTENTSPAGE Refer to Table 1-1 for the complete listing of models available MODELS AVAILABLE RESOLUTIONPower Options Available MODELPOWER RTD MODELS AVAILABLEMODEL Other Models AvailableRESOLUTION TYPENOTES, WARNINGS and CAUTIONS QTY DESCRIPTION SECTION 1 INTRODUCTION 1.1 UNPACKINGcarton in the event reshipment is necessary Unpacking & Inspection 1.2 SAFETY CONSIDERATIONSEMC Considerations Removable Screw-Clamp Cable Connector Display Hold Capability SECTION 2 ABOUT THE METER 2.1 Front of the MeterFeatures Figure 2-1 shows the panel thermometerConnector 2.3 Connector DescriptionConnector Description Signal LoSECTION 3 GETTING STARTED 3.1 Main Board Power Jumpers REMOVE INSTALLAC VOLTAGE Voltage Jumper Pin Settings3.2 Changing the Meter Parameters Refer to Table 1-1, for complete models preface section TABLE 3-2 2-, 3-, 4-Wire, Upscale, Downscale ConfigurationThe following tables summarizes what parameters you can change TABLE 3-1 Range ParametersSENSOR BREAK PROTECTION Section 3.3 Installation and Panel Mounting Figure 3-4. Installation Information 4-Wire RTD 2-Wire RTD3-Wire RTD 3.4 Sensor Input ConnectionsWire colors are for OMEGA RTD wiring only 3.4 Sensor Input Connections ContinuedNote Refer to Table 3-1 and Table 3-2 for internal jumper settings Figure 3-6. 2-Wire RTD Wiring3.5 Analog Output Connections 3.6 Display Hold Connections 3.7 Main Power Connections DC WIRING 3.8 Disassembly/Assembly PULL TAB HERE PC BOARD PUSH HERE SECTION 4 OPERATION AND CALIBRATION 4.1 EQUIPMENT REQUIREDFigure 4-1. 2-Wire Configuration 4.2 CALIBRATION PROCEDUREFigure 4-2. 3-Wire Configuration RESISTANCE CALIBRATION VALUES WHEN YOU ARE USING RESISTANCE SOURCEADJUST METERSECTION 5 SPECIFICATIONS DISPLAY MECHANICAL DIMENSIONSPOWER ENVIRONMENTAL3.78 96.0 TOP VIEW Figure 5-1 Dimensions1.89 48.0 BEZEL BACKPLATE CASE SIDE VIEW 0.76 3.76 95.5 4.32 109.7 MAXSECTION 6 GLOSSARY Page USAWARRANTY/DISCLAIMER RETURN REQUESTS / INQUIRIESPRESSURE, STRAIN AND FORCE TEMPERATUREOMEGAÉOf Course FLOW/LEVEL