OPERATION

TO START ENGINE

Ensure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

Ensure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if yourhouse is nota 120 Volt A.C. three-wire grounded system. Serious personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Push the primer three (3) times.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Connect the power cord to the engine.

6.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

7.Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

8.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

9.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer three (3) times.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” position.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any moisture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

It is easier and more efficient to remove snow imme- diately after it falls.

The best time to remove snow is the early morning. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures.

Slightly overlap each successive path to ensure all snow will be removed.

Throw snow downwind whenever possible.

Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

12

Page 12
Image 12
Husqvarna ST 224 warranty Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen

ST 224 specifications

The Husqvarna ST 224 is a powerful, versatile snowblower designed to tackle even the harshest winter conditions. Built for residential use, this reliable two-stage snow thrower excels in clearing medium to large-sized driveways, sidewalks, and parking areas, efficiently managing snow up to 12 inches deep.

One of the standout features of the ST 224 is its robust engine. It is powered by a reliable 223cc Husqvarna engine, which delivers impressive performance and durability. The engine’s efficient design allows for easy starting, even in frigid temperatures. With a maximum throwing distance of approximately 33 feet, this snowblower can rapidly discharge snow, making quick work of winter's toughest tasks.

The snowblower is equipped with a 24-inch wide clearing width and a 23-inch intake height, allowing it to accommodate heavy snowfall with ease. The auger system efficiently collects snow, while the impeller system provides powerful throwing capabilities. This combination ensures that users can clear snow quickly and efficiently.

Husqvarna has incorporated several user-friendly features into the ST 224, making it easy to operate. The adjustable skid shoes allow users to customize the height of the machine relative to the surface being cleared, preventing damage to driveways or sidewalks. The remote chute rotation and deflector adjustment enable users to aim the snow where they want it to go with minimal effort.

When it comes to maneuverability, the Husqvarna ST 224 shines. It features large, deep-tread wheels that provide excellent traction, even in icy conditions. This mobility is further enhanced by the lightweight construction of the snowblower, making it easy to handle and operate.

The snowblower's durable construction ensures longevity, even during demanding use. The steel frame and housing provide the necessary robustness, while the corrosion-resistant materials ensure that the machine can withstand the wear and tear of winter weather.

Overall, the Husqvarna ST 224 combines power, efficiency, and user-friendly features. It’s an ideal choice for homeowners who need a reliable snowblower that can handle heavy snowfall, offering exceptional performance and ease of use throughout the winter months. With its impressive features and technologies, the Husqvarna ST 224 stands out as a top choice for residential snow removal.