Fostex D2424 manual Executing Erase, Single Undo/Redo Erase, Trim the edit point while previewing

Model D2424 Reference Manual (Editing Tracks)

Checking and adjusting the edit points

After you store the edit points, you can check them on the display by pressing the corresponding keys. You may also adjust the points.

1.While the recorder section is stopped, press and hold down the [SHIFT] key and press the memory

key for which you wish to check the edit point.

You can preview “fade-out” at the AUTO PUNCH IN point and “fade-in” at AUTO PUNCH OUT point.

2.Trim the edit point while previewing.

•Refer to “Preview Function” on page “62” for more information.

Executing Erase

1. Press the [RECORD TRACK] select key to select the track to erase, to set it READY.

You can select a mono track or multiple tracks (including all tracks). The selected track indication flashes.

<Check Points!>

•To erase the data in its entirety from the tracks, you can also use the Program Delete function to erase the entire Program.

In either case, you can expand the recordable area on the disk. Use either one of the erase operations to erase unnecessary data if the recorder displays an alarm message indicating insufficient recordable space for Auto Punch In/Out, Copy & Paste, or Move & Paste.

•To erase the data in its entirety from ABS 0 - REC END, it is recommended that erase end point (AUTO PUNCH OUT point) is stored after the REC END time to ensure through erase performance. To do this, move the recorder section location to the REC END point prior to storing the AUTO PUNCH OUT point, press the [PLAY] button from that location, move the ABS time after the REC END, and store.

The hard disk will not successfully access points after REC END though play is executed after REC END, however, this makes it possible to move up the ABS time.

2.Press the [EDIT] key repeatedly until “Erase” flashes on the display.

3.Press the [EXECUTE/YES] key.

The flashing “Erase” message lights up steadily, and “SURE?” flashes.

Flashing

SURE?

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

Lit

•To cancel the erase operation, press the [STOP] button or the [EXIT/NO] key while “SURE ?” flashes on the display.

4.Press the [EXECUTE/YES] key again.

The recorder starts erasing the data and “Wait Erasing!” flashes. When the erase operation is completed, “COMPLETED !” lights up.

5. Press the [STOP] button or the [EXIT/NO] key.

The recorder exits edit mode and displays the previous Time Base indication.

Single Undo/Redo Erase

You can single undo or redo the Erase operation.

•To restore the data that existed before you erased it, press the [UNDO/REDO] key.

•To restore the data after you undo the Erase operation, press the [UNDO/REDO] key again.

When you press the [UNDO/REDO] key, the recorder will undo or redo the operation immediately, and display “Undo !” or “Redo !” and “COMPLETED !”.

<Note>

This function only works when this recorder is in the stop mode.

<Note>

If you perform one of the following operations after you use the Copy & Paste or Move and Paste operation, the Undo/Redo function will no longer be effective.

1.If a new recording has been made.

2.When a new editing job is executed (such as Copy & Paste, Move & Paste, Erase).

3.While in the AUTO PUNCH ON mode, when the AUTO PUNCH IN point is passed in the PLAY (or RECORD) mode.

4.If the power was switched off.

5.If program select was executed.

6.When multiple undo is executed.

71