Fostex D2424 manual Setup of the Chain Play Mode, Specify the Program and Execute Chain Play

Model D2424 Reference Manual (Chain Play function)

Setup of the Chain Play Mode

Upon setup of the previous “Chain Play List,” select the desired mode in the “Chain Play MD?” (Setup of the chain play mode) menu in the same SETUP mode.

<Note>

The chain play mode setting will be held even though power is switched off, and if power is switched when the D2424 is set to pause mode, the recorder will automatically execute chain play. If chain play is no longer required, reset to “Off” the “Chain Play MD?” menu after ending chain play.

1.Press the [SETUP] key while the D2424 is in the stop mode to switch to the SETUP display.

2.Display the “Chain Play MD?” menu via the [JOG] dial and then press the [EXECUTE/YES] key.

The recorder will change to the display for setting up of the chain play mode and the present setup mode will flash (In the initial setup, “Off” will flash).

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Flashing

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

3.Select the desired mode via the [JOG] dial.

When the [JOG] dial is rotated, modes other than the currently shown “Off” listed below can be selected.

“Off”
“Pause” (Pause mode)	Refer to previous page 57 on
“Auto P” (Auto play mode)	the function of each mode.
“Rpt” (Pepeat mode)

4.Press the [EXECUTE/YES] key after selecting the mode.

The recorder will exit from the SETUP mode after setup is completed.

In this step, if it was completed in the setup other than the “Off” mode, the D2424 will automatically locate to the “AUTO RTN START point” of the first program in the previously setup “Chain list” and stop. If it was completed after setup to “Off,” the D2424 will return to the first display of the program prior to entering the SETUP mode.).

If the D2424 is played back after this, functions of the mode selected will be executed from the first program in the chain list.

Normally, in chain play as explained above, execution starts from the first program on the chain list but any program of your choice can be specified and chain play executed from that program.

For details, refer to “Specify the program and execute chain play”.

<Important>

Be sure the Chain Play List is set up correctly be- fore setting the chain play mode. Each setting of the chain play mode except “Off,” will not function if the previously mentioned “Chain play list” is not set up correctly beforehand. If the mode is executed while set up of with an incorrect list, after display- ing “Illegal P.List!,” the D2424 will automatically go to the previously mentioned “Chain Play List?” menu.

Specify the Program and Execute Chain Play

Specify at random a program set in the chain play list and execute chain play from the program specified. This operation can be executed only when the “Chain Play MD?” menu is set in other than “Off.”

1.Press the [PGM SEL] key while the D2424 is in the stop mode.

After “Select Chain No!,” is displayed, the first number in the present chain play list will flash and the program, and its title, will be displayed.

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24
Flashing
			SURE?																						PGM
OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

2.Select the desired program with the [JOG] dial and press the [EXECUTE/YES] key.

The sequence number currently set in the chain list can be selected by rotating the [JOG] dial. The program /title in selected order will be simultaneously displayed. After selection, when the [EXECUTE/YES] key is pressed, the D2424 will locate to the “AUTO RTN START point” of the selected program.

3.Start playback by pressing the [PLAY] button.

Chain play will be execute in compliance to the currently set “Chain Play MD?” mode.

<Note>

You cannot record or edit in the chain play mode. It will only play back the program set in the chain play list.

59