Fostex D2424 manual Setup of the Chain Play List, Setup example of the chain play list

Model D2424 Reference Manual (Chain Play function)

Setup of the Chain Play List

The chain play list is setup via the “Chain Play List?” menu in the SETUP mode.

The following procedure is based on the assumption that a multiple number of programs are in the current drive and that a tune is recorded in each program.

1.Enter the SETUP mode by pressing the [SETUP] key while the D2424 is in the stop mode.

2.Use the [JOG] dial to display the “Chain Play List?,” and then press the [EXECUTE/YES] key.

The display will change to setup of the play list.

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

	Flashing
SETUP
OL		OL	BIT	24
0	0
3	3			FS
6	6
9	9			kHz
12	12			CLOCK
18	18
24	24			INT
30	30
42	42
∞		∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

This display indicates the initial setting in which no chain list is setup (“EE” means “invalid.”).

The chain play number can be set in the currently blinking section (left) and numbers “01” through “99” can be input via the [JOG] dial.

Also, the flashing section can be moved from the left “01” to the right “EE” by pressing the [EXECUTE/ YES] key, and except for “EE,” each program number currently in the disk can be selected via the [JOG] dial.

3.Input the chain number via the [JOG] dial and press the [EXECUTE/YES] key.

The flashing section will move from left to the right “EE.”

Flashing

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

4.Select the desired program number via the [JOG] dial and press the [EXECUTE/YES] key.

The chain number of the selected program will be set and, the same as in <Step 2>, the left section will flash. For example, if it has been set as shown below, the setting will be for playback of the program 5 tune in the second order.

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

Repeat these procedures to set up the chain play number in the desired program.

<Setup example of the chain play list>

As an example, if the chain play list is set as shown below, chain play is possible in the order of: program 3 - program 5 - program 2. If the chain list is to be ended after program 1, as shown in the example below, set “EE” at fourth (“c04”) in the chain list.

By selecting “EE,” the chain play list setting will be “c01” - “c03,” and beyond “c04” will be invalid.

“EE” can be selected with the [JOG] dial while the right program number is flashing.

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

SETUP

OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

SETUP

OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

<Note>

*In order to execute chain play, “AUTO RTN START point” and “AUTO RTN END point” must be setup in each program to be played back. Refer to previous page “50” for how to register memory points.

*If the chain play list is edited even once, the Chain Play Mode will be set “OFF.”

In such case, after setup of the chain play list, reset the Chain Play Mode to “ON” .

58