Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 Command Summary, Terse Verbose, Command Availability, Function, Enter

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 51

Terse Verbose

The table below summarizes the various response messages for both the Terse and Verbose modes.

Terse Verbose

0 OK

0RAM Test Passed

1Connected *

2Busy

3Disconnected

4Invalid Command

5Are You Sure (Y/N) ?

6Invalid Parameter

7Invalid Syntax

8Invalid Access

9Enter Site ID:

AAborted

BEnter Password:

CInvalid Password

DRAM Test Failed at *

EInactivity Timeout, Disconnected

FData in Buffer from Previous Connection ...

Re-Enter Logoff Sequence to Purge Buffer.

GAsleep

*These verbose Response Messages include additional information not provided by terse Response Messages.

10.3. Command Summary

				Command Availability
Function		Command Syntax
Function		Command Syntax		Supervisor		User
Enter Command Mode		[Enter]		X		X
Exit Command Mode		/X [Enter]		X		X
Help Menu		/H [Enter]		X		X
Display Site ID		/J [Enter]		X		X

Image 51

Western Telematic CMS-16 Command Summary, Terse Verbose, Command Availability, Function, Command Syntax, Supervisor, Enter

Contents

WTI Part No Rev. B Console Management SwitchCMS-16 Users GuideRack Mount Installation No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Battery Replacement3.4. Connecting your PC to the CMS Table of ContentsDisconnect Power 3.2. Apply Power to the CMS 3.3. System SetUp Ports4.2.3. Default Response Message Format Sw6 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw57.4. Modem Mode 8. Saving and Restoring Configuration Parameters 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer Mode 7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port BuffersConfiguration Backup 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Limited Command AccessCOURIER FONT 2. Unit Description2.1. Front Panel Typographic Conventions2.2. Back Panel 2. Power Cable Receptacle 3. Power SwitchUsing Other Parameters for this Overview Optional 3. Getting Started3.1. Communication Parameters 3.5. Communicating with the CMS Unit 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.4. Connecting your PC to the CMS2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.2. Configure Option Switches 4.1.1. AC Powered Units4.1.2. DC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.3. Initialize Unit to Default Settings 4.2.3. Default Response Message Format Sw64.2.4. Default Command Echo Sw7 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecuritySecurity Mask #1 Mask #1 Action Deny Security Mask #2 Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit5.6. Copying Parameters to All Ports 6. The Status Screens 5.7. Save User Selected Parameters6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1. Any-to-Any Mode 7. Operation7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 4 Enter D 3 EnterD 4 Enter Hunt Group Example 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer ModeHunt Group Example 7.3.1. Reading Data from Buffer Mode Ports C xx EnterE xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8. Saving and Restoring Configuration Parameters 8.1. Sending Parameters to a File8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Terse Verbose 10.3. Command SummaryCommand Availability Command Syntax1 Supervisor Mode displays parameters for all ports Format EnterxxxEnter 10.4. Command SetEnter Enter Command Mode Enter+++Enter Resident Disconnect SequenceD Third Party Disconnect Format /C x x EnterCP Copy RS232 Port Parameters Format /CP EnterFormat /E/Y x x Enter Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter E Erase BufferFormat /H Enter I Default and TestFormat /F Enter H HelpP Set RS232 Port Parameters Format /J EnterN Set Network Port Parameters Format /N EnterSN Display Network Status SD Display Port DiagnosticsT Reset Network Port Format /SD EnterW Display Port Parameters Who UF Upgrade FirmwareX Exit Command Mode Format /UF EnterAppendix B. Specifications Appendix A. RS232 Port InterfaceFormat /X Enter Appendix C. Customer Service PowerStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information