Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 UF Upgrade Firmware, Format /UF Enter, W Display Port Parameters Who

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 59

/UF Upgrade Firmware

/UF Upgrade Firmware

When new versions of the CMS operating firmware become available, this command is used to update the existing firmware as described in Section 9. Note that this command will only function at the Network Port and at Setup Ports One and Two.

Availability: Supervisor Only

Format: /UF [Enter]

Response: The CMS will display a menu which offers the options to retain existing CMS parameters, default parameters, or abort the upgrade procedure.

/W Display Port Parameters (Who)

Displays configuration of an individual port, but does not allow the user to change parameters. Ports with User Level command capability cannot display parameters for other ports. Normally, the Port Parameters screen will not include the Port Password. Note however, that when the Supervisor Mode is active, the /WP option can be used to display the password for the target port. For more information, please refer to Section 6.4.

Availability: Supervisor / User

Format: /W[P] [x] [Enter]

Where:

PWhen the "P" option is included (e.g. /WP 5), the Port Parameters screen will list the password for each port, if defined. (Supervisor Mode Only).

xIs the port number or name. To display parameters for the Network Port, enter an "N". If the "x" argument is omitted, parameters for your resident port will be displayed.

Response: Displays port parameters.

Example: To display parameters for a port named "SERVER", access the Command Mode from a port with Supervisor Level command capability, and type /W SERVER [Enter].

/X Exit Command Mode

Exits Command Mode, When issued at the Net Port, also ends the telnet session. Note that exiting from Command Mode will not terminate port connections.

●Any-to-Any Mode: Exits Command Mode.

●Modem Mode: Disconnects and resets modem, hang-up message is sent, hardware line to modem drops for 500 ms, and reset message is sent.

Image 59

Western Telematic CMS-16 manual UF Upgrade Firmware, Format /UF Enter, W Display Port Parameters Who, Format /WP x Enter

Contents

WTI Part No Rev. B Console Management SwitchCMS-16 Users GuideRack Mount Installation No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Battery Replacement3.4. Connecting your PC to the CMS Table of ContentsDisconnect Power 3.2. Apply Power to the CMS 3.3. System SetUp Ports4.2.3. Default Response Message Format Sw6 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw57.4. Modem Mode 8. Saving and Restoring Configuration Parameters 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer Mode 7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port BuffersConfiguration Backup 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Limited Command AccessCOURIER FONT 2. Unit Description2.1. Front Panel Typographic Conventions2.2. Back Panel 2. Power Cable Receptacle 3. Power Switch3.1. Communication Parameters Using Other Parameters for this Overview Optional3. Getting Started 3.5. Communicating with the CMS Unit 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.4. Connecting your PC to the CMS2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.1.2. DC Powered Units 4.2. Configure Option Switches4.1.1. AC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.2.4. Default Command Echo Sw7 4.3. Initialize Unit to Default Settings4.2.3. Default Response Message Format Sw6 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecuritySecurity Mask #1 Mask #1 Action Deny Security Mask #2 Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit5.6. Copying Parameters to All Ports 6.1. The Port Status Screen /S 6. The Status Screens5.7. Save User Selected Parameters Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1.1. Port Connection and Disconnection 7.1. Any-to-Any Mode7. Operation 2. Invoke the /C command to connect the desired ports D 4 Enter D 3 4 EnterD 3 Enter Hunt Group Example 7.1.2. Defining Hunt GroupsHunt Group Example 7.2. Passive Mode7.3. Buffer Mode E xx Enter 7.3.1. Reading Data from Buffer Mode PortsC xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8.2. Restoring Saved Parameters 8. Saving and Restoring Configuration Parameters8.1. Sending Parameters to a File 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Terse Verbose 10.3. Command SummaryCommand Availability Command Syntax1 Supervisor Mode displays parameters for all ports Format EnterxxxEnter 10.4. Command SetEnter Enter Command Mode Enter+++Enter Resident Disconnect SequenceD Third Party Disconnect Format /C x x EnterCP Copy RS232 Port Parameters Format /CP EnterFormat /E/Y x x Enter Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter E Erase BufferFormat /H Enter I Default and TestFormat /F Enter H HelpP Set RS232 Port Parameters Format /J EnterN Set Network Port Parameters Format /N EnterSN Display Network Status SD Display Port DiagnosticsT Reset Network Port Format /SD EnterW Display Port Parameters Who UF Upgrade FirmwareX Exit Command Mode Format /UF EnterFormat /X Enter Appendix B. SpecificationsAppendix A. RS232 Port Interface Stop Bits 1 or Appendix C. Customer ServicePower Trademarks Used in this Manual Trademark and Copyright Information