Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 manual WP xx Enter

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 39

/W[P] xx [Enter]

PORT PARAMETERS #03:
1.	Port Name:	(undefined)
2.	Password:	(undefined)
3.	Baud Rate:	9600
4.	Bits/Parity:	8-None
5.	Stop Bits:	1
6.	Handshake Mode:	RTS/CTS
7.	Port Mode:	Any-to-Any
	74. DTR Output:	Pulse
8.	Supervisor Mode:	Permit
9.	Logoff Character:	+

10.Sequence Disconnect: Three Characters

11.Timeout Disconnect: Off

12.	Response Type:	Verbose
13.	Command Echo:	On
14.	Accept Break:	Yes

Enter: "<" previous port, ">" next port, <ESC> exit ...

Figure 6.4: The Port Parameters Screen (RS232 Port Shown)

The /W command is available in both Supervisor Mode and User Mode. Note however, that when you log in with a Port (User) password, the CMS will only display information regarding your resident port.

When the Supervisor Mode is active, the Port Parameters Screens offer the option to either display or suppress the Port Passwords. Normally, when the /W command is invoked, the Password field will read either "defined" or "undefined", depending upon whether or not the password for that port has been specified. To display the Port Parameters Screen with the Port Password, type /WP, followed by the desired port number, and then press [Enter]. Note that the /WP command option is not available in User Mode.

The /W command uses the following format:

/W[P] xx [Enter]

Where:

PIs the command option to display port passwords. Note that when this option is included (e.g. /WP 5), the Port Parameters Screen will display the Port Password, if defined. (Supervisor Mode Only).

xxis the desired port number. If the letter "N" is entered in place of a port number, the /W command will display parameters for the Network Port.

Note: When the command mode is accessed via the Network Port using a Port

Image 39

Western Telematic CMS-16 manual WP xx Enter

Contents

WTI Part No Rev. B Console Management SwitchCMS-16 Users GuideRack Mount Installation No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Battery Replacement3.4. Connecting your PC to the CMS Table of ContentsDisconnect Power 3.2. Apply Power to the CMS 3.3. System SetUp Ports4.2.3. Default Response Message Format Sw6 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw57.4. Modem Mode 8. Saving and Restoring Configuration Parameters 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer Mode 7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port BuffersConfiguration Backup 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Limited Command AccessCOURIER FONT 2. Unit Description2.1. Front Panel Typographic Conventions2.2. Back Panel 2. Power Cable Receptacle 3. Power SwitchUsing Other Parameters for this Overview Optional 3. Getting Started3.1. Communication Parameters 3.5. Communicating with the CMS Unit 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.4. Connecting your PC to the CMS2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.2. Configure Option Switches 4.1.1. AC Powered Units4.1.2. DC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.3. Initialize Unit to Default Settings 4.2.3. Default Response Message Format Sw64.2.4. Default Command Echo Sw7 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecuritySecurity Mask #1 Mask #1 Action Deny Security Mask #2 Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit5.6. Copying Parameters to All Ports 6. The Status Screens 5.7. Save User Selected Parameters6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1. Any-to-Any Mode 7. Operation7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 4 Enter D 3 EnterD 4 Enter Hunt Group Example 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer ModeHunt Group Example 7.3.1. Reading Data from Buffer Mode Ports C xx EnterE xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8. Saving and Restoring Configuration Parameters 8.1. Sending Parameters to a File8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Terse Verbose 10.3. Command SummaryCommand Availability Command Syntax1 Supervisor Mode displays parameters for all ports Format EnterxxxEnter 10.4. Command SetEnter Enter Command Mode Enter+++Enter Resident Disconnect SequenceD Third Party Disconnect Format /C x x EnterCP Copy RS232 Port Parameters Format /CP EnterFormat /E/Y x x Enter Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter E Erase BufferFormat /H Enter I Default and TestFormat /F Enter H HelpP Set RS232 Port Parameters Format /J EnterN Set Network Port Parameters Format /N EnterSN Display Network Status SD Display Port DiagnosticsT Reset Network Port Format /SD EnterW Display Port Parameters Who UF Upgrade FirmwareX Exit Command Mode Format /UF EnterAppendix B. Specifications Appendix A. RS232 Port InterfaceFormat /X Enter Appendix C. Customer Service PowerStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information