Western Telematic CMS-16 guide

■4.1.2. DC Powered Units

❍4.2. Configure Option Switches

■4.2.1. Default Baud Rate (Sw1, Sw2, Sw3)

■4.2.2. Default Handshake (Sw4, Sw5)

■4.2.3. Default Response Message Format (Sw6)

■4.2.4. Default Command Echo (Sw7)

❍4.3. Initialize Unit to Default Settings

❍4.4. Connecting Devices to the CMS

❍4.5. Application Example

●5. Configuration

❍5.1. Access to the CMS Command Mode

❍5.2. System SetUp Ports

❍5.3. Password Functions

■5.3.1. The Supervisor Password

■5.3.2. The Port Passwords

❍5.4. Defining the Site ID and Supervisor Password

❍5.5. Port Configuration

■5.5.1. Configuration Conventions

■5.5.2. Port Modes

■5.5.3. RS232 Port Configuration Menus

■5.5.4. Network Port Configuration Menu

■5.5.5. Implementing IP Security

❍5.6. Copying Parameters to All Ports

❍5.7. Save User Selected Parameters

●6. The Status Screens

❍6.1. The Port Status Screen (/S)

❍6.2. The Port Diagnostics Screen (/SD)

❍6.3. The Network Status Screen (/SN)

❍6.4. The Port Parameters Screens (/W)

●7. Operation

❍7.1. Any-to-Any Mode

■7.1.1. Port Connection and Disconnection

■7.1.1.1. Connecting Ports

Image 4

Western Telematic CMS-16 manual

Contents

CMS-16 Battery Replacement Nameplate Power WarningRack Mount Installation Table of Contents Page Appendices List of Figures Introduction Front Panel Unit DescriptionTypographic Conventions Power Cable Receptacle Power Switch Back Panel Getting Started Using Other Parameters for this Overview OptionalCommunication Parameters Apply Power to the CMS System SetUp PortsConnecting your PC to the CMS Communicating with the CMS Unit Command Menu Display Configuration Control Port Name Password Status Hardware Installation Connecting Power to the CMS Unit AC Powered Units Configure Option SwitchesDC Powered Units Default Baud Rate Sw1, Sw2, Sw3 Default Handshake Sw4, Sw5 Default Response Message Format Sw6 Initialize Unit to Default SettingsDefault Command Echo Sw7 Connecting Devices to the CMS Application Example CMS Application Example Not to Scale Configuration Access to the CMS Command Mode $ telnet 192.1.1.1 Enter Password Functions Supervisor Password Defining the Site ID and Supervisor Password Port Passwords Port Configuration Configuration Conventions 3. RS232 Port Configuration Menus Port Modes Port Parameters #02 CTS/RTS Parameters #02 Stop Bits Default =ATZ AT&C1$D2S0=1 Network Port Configuration Menu Network Parameters Telnet Port ParametersPage Implementing IP Security IP SecurityPage Copying Parameters to All Ports Copy Port Parameters Save User Selected Parameters Status ScreensPort Status Screen /S Status Mode Buffer Count Port Status Screen Supervisor Mode, Defaults Shown Port Diagnostics Screen /SD DiagnosticsMode BUF CTS Name Status Network Status Screen /SN Port Parameters Screens /W Network Status LAN StatusTelnet Port Status CMS Port Parameters #03 RTS/CTS Operation Any-to-Any ModePort Connection and Disconnection Disconnecting Ports Enter Defining Hunt Groups Hunt Group Example Passive Mode Buffer Mode Reading Data from Buffer Mode Ports Xx Enter Modem Mode Port Buffers Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Upgrading CMS Firmware Command Reference Guide Command Conventions Command Response Command Summary Terse Verbose WP n Enter Command Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence Connect Format /C x x Enter CP Copy RS232 Port ParametersFormat /CP Enter Third Party Disconnect Format /D/Y x x Enter 2 Enter or /D/Y 3 EnterErase Buffer Format /E/Y x x Enter Help Default and TestDisplay Site ID Set RS232 Port Parameters Set Network Port ParametersDisplay Port Status SD Display Port Diagnostics Reset Network PortSN Display Network Status Save Parameters UF Upgrade Firmware Exit Command ModeFormat /UF Enter Display Port Parameters Who Appendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual