Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 manual Format /J Enter, N Set Network Port Parameters, Format /N Enter

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 57

Format: /J [Enter]

Format: /J [Enter]

Response: Displays Site I.D. Message

/N Set Network Port Parameters

Displays a menu which is used to define communication parameters for the Network Port. Also allows access to the IP Security function, which is used to restrict network access by unauthorized IP addresses. For more information on selecting network parameters, please refer to Section 5.5.4.

Availability: Supervisor Only

Format: /N [Enter]

Response: Displays Network Parameters Menu

/P Set RS232 Port Parameters

Displays a menu which allows the user to select options and parameters for the selected port. Section 5.5.3 describes the procedure for defining port parameters.

Availability: Supervisor Only

Format: /P [x] [Enter]

Where x is the number or name of the port to be configured. If the port number or name is not specified, the CMS will display the configuration menu for your resident port.

Response: The Port Parameters Menu is displayed.

/S Display Port Status

Displays the Port Status Screen, which lists current conditions and parameters for all ports. Normally, the Port Status Screen will not display Port Passwords; the Password column will read either "defined" or "undefined", depending upon whether or not the password for each port has been specified. When the Supervisor Mode is active, the /SP command offers the option to either display or suppress Port Passwords. For more information on the Port Status Screen, please refer to Section 6.1.

Availability: Supervisor / User

Format: /S[P] [Enter]

When the "P" option is included (e.g. /SP), the Port Status Screen will lists the password for each port, if defined. (Supervisor Mode Only).

Response: Displays Port Status Screen

Image 57

Western Telematic CMS-16 Format /J Enter, N Set Network Port Parameters, Format /N Enter, P Set RS232 Port Parameters

Contents

CMS-16 Console Management SwitchUsers Guide WTI Part No Rev. BNameplate Power Warning No Serviceable Parts Inside Authorized Service Personnel OnlyBattery Replacement Rack Mount InstallationDisconnect Power Table of Contents3.2. Apply Power to the CMS 3.3. System SetUp Ports 3.4. Connecting your PC to the CMS4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.2. Default Handshake Sw4, Sw5 4.2.3. Default Response Message Format Sw67.2. Passive Mode 7.3. Buffer Mode 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port Buffers 7.4. Modem Mode 8. Saving and Restoring Configuration Parameters6.2. The Port Diagnostics Screen Defaults Shown 6.1. The Port Status Screen Supervisor Mode, Defaults ShownLimited Command Access Configuration Backup2.1. Front Panel 2. Unit DescriptionTypographic Conventions COURIER FONT2.2. Back Panel 2. Power Cable Receptacle 3. Power SwitchUsing Other Parameters for this Overview Optional 3. Getting Started3.1. Communication Parameters 3.3. System SetUp Ports 3.2. Apply Power to the CMS3.4. Connecting your PC to the CMS 3.5. Communicating with the CMS Unit2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.2. Configure Option Switches 4.1.1. AC Powered Units4.1.2. DC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.3. Initialize Unit to Default Settings 4.2.3. Default Response Message Format Sw64.2.4. Default Command Echo Sw7 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecurityExample 2 Allow access only by addresses that begin with Example 1 Deny access to all hosts except Security Mask #1Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit Security Mask #1 Mask #1 Action Deny Security Mask #25.6. Copying Parameters to All Ports 6. The Status Screens 5.7. Save User Selected Parameters6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1. Any-to-Any Mode 7. Operation7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 4 Enter D 3 EnterD 4 Enter Hunt Group Example 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer ModeHunt Group Example 7.3.1. Reading Data from Buffer Mode Ports C xx EnterE xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8. Saving and Restoring Configuration Parameters 8.1. Sending Parameters to a File8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Command Availability 10.3. Command SummaryCommand Syntax Terse Verbose1 Supervisor Mode displays parameters for all ports Enter Enter Command Mode 10.4. Command SetEnter+++Enter Resident Disconnect Sequence Format EnterxxxEnterCP Copy RS232 Port Parameters Format /C x x EnterFormat /CP Enter D Third Party DisconnectD/Y 2 Enter or /D/Y 3 Enter Format /D/Y x x EnterE Erase Buffer Format /E/Y x x EnterFormat /F Enter I Default and TestH Help Format /H EnterN Set Network Port Parameters Format /J EnterFormat /N Enter P Set RS232 Port ParametersT Reset Network Port SD Display Port DiagnosticsFormat /SD Enter SN Display Network StatusX Exit Command Mode UF Upgrade FirmwareFormat /UF Enter W Display Port Parameters WhoAppendix B. Specifications Appendix A. RS232 Port InterfaceFormat /X Enter Appendix C. Customer Service PowerStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information