Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 Format /C x x Enter, CP Copy RS232 Port Parameters, Format /CP Enter

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 54

Format: /C <x> [x] [Enter]

Establishes a bi-directional connection between two ports. For more information and command line examples, please refer to Section 7.1. There are two different types of port connections:

●Resident Connect: If the /C command specifies one port name or number, your resident port will be connected to the specified port.

●Third Party Connect: If the /C command specifies two port names or numbers, the unit will connect the two ports indicated. A Third Party Connect command must be issued from a third port with "Supervisor" command capability. "User" ports cannot initiate a Third Party Connect.

Note:

●Ports with "User" command capability can only connect to ports that share the same Port Password.

●Ports with "Supervisor" command capability are allowed to connect to all other ports.

Availability: Supervisor / User

Format: /C <x> [x] [Enter]

Where x is the number or name of the port(s) to be connected.

Response:

Verbose: Connected xx, when a Resident Connection is initiated, the CMS will also display the currently selected Resident Disconnect Sequence for your port.

Terse: 1

/CP Copy RS232 Port Parameters

Allows quick set-up when all CMS RS232 ports will be configured with the same or similar parameters. When the /CP command is invoked, the CMS will display a menu that is used to select common port parameters, which can then be copied to all CMS RS232 ports. For more information, please refer to Section 5.6.

Availability: Supervisor Only

Format: /CP [Enter]

Response: Displays Copy Parameters Menu

/D Third Party Disconnect

Invoke the /D command at your resident port to disconnect two other ports. The /D command cannot be used to disconnect your resident port. To disconnect your resident port, issue the

Image 54

Western Telematic CMS-16 Format /C x x Enter, CP Copy RS232 Port Parameters, Format /CP Enter, D Third Party Disconnect

Contents

Users Guide Console Management SwitchCMS-16 WTI Part No Rev. BBattery Replacement No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Rack Mount Installation3.2. Apply Power to the CMS 3.3. System SetUp Ports Table of ContentsDisconnect Power 3.4. Connecting your PC to the CMS4.2.2. Default Handshake Sw4, Sw5 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.3. Default Response Message Format Sw67.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port Buffers 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer Mode 7.4. Modem Mode 8. Saving and Restoring Configuration ParametersLimited Command Access 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Configuration BackupTypographic Conventions 2. Unit Description2.1. Front Panel COURIER FONT2. Power Cable Receptacle 3. Power Switch 2.2. Back PanelUsing Other Parameters for this Overview Optional 3. Getting Started3.1. Communication Parameters 3.4. Connecting your PC to the CMS 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.5. Communicating with the CMS Unit2. Press Enter to access the CMS Command Mode Figure 3.2 The Port Status Screen Defaults Shown Figure 3.1 The Supervisor Level Help Screen4. Hardware Installation 4.1. Connecting Power to the CMS Unit4.2. Configure Option Switches 4.1.1. AC Powered Units4.1.2. DC Powered Units 4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw54.3. Initialize Unit to Default Settings 4.2.3. Default Response Message Format Sw64.2.4. Default Command Echo Sw7 4.4. Connecting Devices to the CMS 4.5. Application ExampleFigure 4.2 CMS Application Example Not to Scale 5. Configuration 5.1. Access to the CMS Command Mode5.2. System SetUp Ports $ telnet 192.1.1.1 Enter5.3. Password Functions 5.3.1. The Supervisor Password5.4. Defining the Site ID and Supervisor Password 5.3.2. The Port Passwords5.5. Port Configuration 5.5.1. Configuration Conventions5.5.3. RS232 Port Configuration Menus 5.5.2. Port ModesTo select port parameters, proceed as follows 5. Stop Bits Default = AT&C1$D2S0=1 Figure 5.2 Port Configuration Menu Modem Mode5.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On 5.5.5. Implementing IP Security Figure 5.4 IP Security MenuMask #1 Action Deny Security Mask #2 Mask #2 Action Permit Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Security Mask #1 Mask #1 Action Deny Security Mask #25.6. Copying Parameters to All Ports 6. The Status Screens 5.7. Save User Selected Parameters6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN 6.4. The Port Parameters Screens /W Figure 6.3 The Network Status Screen Defaults ShownWP xx Enter 7.1. Any-to-Any Mode 7. Operation7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 4 Enter D 3 EnterD 4 Enter 7.1.2. Defining Hunt Groups Hunt Group Example7.2. Passive Mode 7.3. Buffer ModeHunt Group Example 7.3.1. Reading Data from Buffer Mode Ports C xx EnterE xx Enter 7.4. Modem Mode 7.3.2. Port Buffers8. Saving and Restoring Configuration Parameters 8.1. Sending Parameters to a File8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10. Command Reference Guide 10.1. Command Conventions10.2. Command Response Command Syntax 10.3. Command SummaryCommand Availability Terse Verbose1 Supervisor Mode displays parameters for all ports Enter+++Enter Resident Disconnect Sequence 10.4. Command SetEnter Enter Command Mode Format EnterxxxEnterFormat /CP Enter Format /C x x EnterCP Copy RS232 Port Parameters D Third Party DisconnectE Erase Buffer Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter Format /E/Y x x EnterH Help I Default and TestFormat /F Enter Format /H EnterFormat /N Enter Format /J EnterN Set Network Port Parameters P Set RS232 Port ParametersFormat /SD Enter SD Display Port DiagnosticsT Reset Network Port SN Display Network StatusFormat /UF Enter UF Upgrade FirmwareX Exit Command Mode W Display Port Parameters WhoAppendix B. Specifications Appendix A. RS232 Port InterfaceFormat /X Enter Appendix C. Customer Service PowerStop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual