Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 Trademark and Copyright Information, Trademarks Used in this Manual

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 62

Trademark and Copyright Information

Trademark and Copyright Information

WTI and Western Telematic are trademarks of Western Telematic Inc.. All other product names mentioned in this publication are trademarks or registered trademarks of their respective companies.

Information and descriptions contained herein are the property of Western Telematic Inc. Such information and descriptions may not be copied, disseminated, or distributed without the express written consent of Western Telematic Inc.

© Copyright Western Telematic Inc. 2000.

Printed in the United States of America.

February, 2000

Part Number: 13027, Revision: B

Trademarks Used in this Manual

ProComm and ProComm Plus are registered trademarks of Datastorm Technologies, Inc.

[ Home User's Guide Archive NetReach Products DataReach Products PollCat Products Contact WTI ]

Image 62

Western Telematic CMS-16 manual Trademark and Copyright Information, Trademarks Used in this Manual

Contents

Users Guide Console Management SwitchCMS-16 WTI Part No Rev. BBattery Replacement No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Rack Mount Installation3.2. Apply Power to the CMS 3.3. System SetUp Ports Table of ContentsDisconnect Power 3.4. Connecting your PC to the CMS4.2.2. Default Handshake Sw4, Sw5 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.3. Default Response Message Format Sw67.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port Buffers 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.2. Passive Mode 7.3. Buffer Mode 7.4. Modem Mode 8. Saving and Restoring Configuration ParametersLimited Command Access 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Configuration BackupTypographic Conventions 2. Unit Description2.1. Front Panel COURIER FONT2. Power Cable Receptacle 3. Power Switch 2.2. Back Panel3.1. Communication Parameters Using Other Parameters for this Overview Optional3. Getting Started 3.4. Connecting your PC to the CMS 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.5. Communicating with the CMS Unit2. Press Enter to access the CMS Command Mode Figure 3.2 The Port Status Screen Defaults Shown Figure 3.1 The Supervisor Level Help Screen4. Hardware Installation 4.1. Connecting Power to the CMS Unit4.1.2. DC Powered Units 4.2. Configure Option Switches4.1.1. AC Powered Units 4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw54.2.4. Default Command Echo Sw7 4.3. Initialize Unit to Default Settings4.2.3. Default Response Message Format Sw6 4.4. Connecting Devices to the CMS 4.5. Application ExampleFigure 4.2 CMS Application Example Not to Scale 5. Configuration 5.1. Access to the CMS Command Mode5.2. System SetUp Ports $ telnet 192.1.1.1 Enter5.3. Password Functions 5.3.1. The Supervisor Password5.4. Defining the Site ID and Supervisor Password 5.3.2. The Port Passwords5.5. Port Configuration 5.5.1. Configuration Conventions5.5.3. RS232 Port Configuration Menus 5.5.2. Port ModesTo select port parameters, proceed as follows 5. Stop Bits Default = AT&C1$D2S0=1 Figure 5.2 Port Configuration Menu Modem Mode5.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On 5.5.5. Implementing IP Security Figure 5.4 IP Security MenuMask #1 Action Deny Security Mask #2 Mask #2 Action Permit Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Security Mask #1 Mask #1 Action Deny Security Mask #25.6. Copying Parameters to All Ports 6.1. The Port Status Screen /S 6. The Status Screens5.7. Save User Selected Parameters Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN 6.4. The Port Parameters Screens /W Figure 6.3 The Network Status Screen Defaults ShownWP xx Enter 7.1.1. Port Connection and Disconnection 7.1. Any-to-Any Mode7. Operation 2. Invoke the /C command to connect the desired ports D 4 Enter D 3 4 EnterD 3 Enter 7.1.2. Defining Hunt Groups Hunt Group ExampleHunt Group Example 7.2. Passive Mode7.3. Buffer Mode E xx Enter 7.3.1. Reading Data from Buffer Mode PortsC xx Enter 7.4. Modem Mode 7.3.2. Port Buffers8.2. Restoring Saved Parameters 8. Saving and Restoring Configuration Parameters8.1. Sending Parameters to a File 9. Upgrading CMS Firmware 10. Command Reference Guide 10.1. Command Conventions10.2. Command Response Command Syntax 10.3. Command SummaryCommand Availability Terse Verbose1 Supervisor Mode displays parameters for all ports Enter+++Enter Resident Disconnect Sequence 10.4. Command SetEnter Enter Command Mode Format EnterxxxEnterFormat /CP Enter Format /C x x EnterCP Copy RS232 Port Parameters D Third Party DisconnectE Erase Buffer Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter Format /E/Y x x EnterH Help I Default and TestFormat /F Enter Format /H EnterFormat /N Enter Format /J EnterN Set Network Port Parameters P Set RS232 Port ParametersFormat /SD Enter SD Display Port DiagnosticsT Reset Network Port SN Display Network StatusFormat /UF Enter UF Upgrade FirmwareX Exit Command Mode W Display Port Parameters WhoFormat /X Enter Appendix B. SpecificationsAppendix A. RS232 Port Interface Stop Bits 1 or Appendix C. Customer ServicePower Trademark and Copyright Information Trademarks Used in this Manual