Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 manual Format /D/Y x x Enter, D/Y 2 Enter or /D/Y 3 Enter, E Erase Buffer

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 55

Format: /D[/Y] <x> [x] [Enter]

Resident Disconnect Sequence or wait for the Timeout Period to elapse (if enabled).

Availability: Supervisor Only

Format: /D[/Y] <x> [x] [Enter]

Where:

/Y (Optional) suppresses the "Sure?" prompt.

xIs the number or name of the port(s) to be disconnected. To Disconnect all ports, enter an asterisk. To disconnect the Network Port, enter an "N".

Response:

Verbose: "Are you Sure (y/n)?", if Y, unit will respond with "Disconnected".

Terse: 5, if Y, unit will respond with 3.

Example: To disconnect Port 2 from Port 3 without the "Sure?" prompt, access the Command Mode from a third port with "All" command capability and type one of the following commands:

/D/Y 2 [Enter] or /D/Y 3 [Enter]

/E Erase Buffer

Erases data from the buffer for a specified port or several ports. Note that erased data cannot be recovered.

Availability: Supervisor Only

Format: /E[/Y] <x> [x] [Enter]

Where:

xIs the number or name of the port buffer(s) to be cleared. To erase buffers for all ports, enter an asterisk.

/Y (Optional) Suppresses the "SURE? (Y/N)" prompt.

Response:

Verbose: "Are You Sure (y/n)?", if Y, the unit will respond with "OK".

Terse: 5, if Y, the unit will respond with 0.

Example: To clear the buffer for Port 3, access the Command Mode from a port with "All" command capability, and type /E 3 [Enter].

/F Set System Parameters

Displays a menu which is used to define the Site ID message and Supervisor Password. When the Supervisor Password is defined, the CMS will display a password prompt before allowing

Image 55

Western Telematic CMS-16 manual Format /D/Y x x Enter, D/Y 2 Enter or /D/Y 3 Enter, E Erase Buffer, Format /E/Y x x Enter

Contents

WTI Part No Rev. B Console Management SwitchCMS-16 Users GuideRack Mount Installation No Serviceable Parts Inside Authorized Service Personnel OnlyNameplate Power Warning Battery Replacement3.4. Connecting your PC to the CMS Table of ContentsDisconnect Power 3.2. Apply Power to the CMS 3.3. System SetUp Ports4.2.3. Default Response Message Format Sw6 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw510.1. Command Conventions 10.2. Command Response 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.4. Modem Mode 8. Saving and Restoring Configuration Parameters 9. Upgrading CMS Firmware 10. Command Reference GuideConfiguration Backup 6.1. The Port Status Screen Supervisor Mode, Defaults Shown6.2. The Port Diagnostics Screen Defaults Shown Limited Command AccessCOURIER FONT 2. Unit Description2.1. Front Panel Typographic Conventions2.2. Back Panel 2. Power Cable Receptacle 3. Power Switch3. Getting Started Using Other Parameters for this Overview Optional3.1. Communication Parameters 3.5. Communicating with the CMS Unit 3.2. Apply Power to the CMS3.3. System SetUp Ports 3.4. Connecting your PC to the CMS2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.1.1. AC Powered Units 4.2. Configure Option Switches4.1.2. DC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.2.3. Default Response Message Format Sw6 4.3. Initialize Unit to Default Settings4.2.4. Default Command Echo Sw7 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecuritySecurity Mask #1 Mask #1 Action Deny Security Mask #2 Example 1 Deny access to all hosts except Security Mask #1Example 2 Allow access only by addresses that begin with Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit5.6. Copying Parameters to All Ports 5.7. Save User Selected Parameters 6. The Status Screens6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1. Any-to-Any Mode 7. Operation7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 Enter D 3 4 EnterD 4 Enter Hunt Group Example 7.1.2. Defining Hunt Groups7.3. Buffer Mode 7.2. Passive ModeHunt Group Example C xx Enter 7.3.1. Reading Data from Buffer Mode PortsE xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8.1. Sending Parameters to a File 8. Saving and Restoring Configuration Parameters8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Terse Verbose 10.3. Command SummaryCommand Availability Command Syntax1 Supervisor Mode displays parameters for all ports Format EnterxxxEnter 10.4. Command SetEnter Enter Command Mode Enter+++Enter Resident Disconnect SequenceD Third Party Disconnect Format /C x x EnterCP Copy RS232 Port Parameters Format /CP EnterFormat /E/Y x x Enter Format /D/Y x x EnterD/Y 2 Enter or /D/Y 3 Enter E Erase BufferFormat /H Enter I Default and TestFormat /F Enter H HelpP Set RS232 Port Parameters Format /J EnterN Set Network Port Parameters Format /N EnterSN Display Network Status SD Display Port DiagnosticsT Reset Network Port Format /SD EnterW Display Port Parameters Who UF Upgrade FirmwareX Exit Command Mode Format /UF EnterAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademarks Used in this Manual Trademark and Copyright Information