Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 manual Appendices, List of Figures, Passive Mode 7.3. Buffer Mode

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 5

■7.1.1.2. Disconnecting Ports

■7.1.2. Defining Hunt Groups

❍7.2. Passive Mode

❍7.3. Buffer Mode

■7.3.1. Reading Data from Buffer Mode Ports

■7.3.2. Port Buffers

❍7.4. Modem Mode

●8. Saving and Restoring Configuration Parameters

❍8.1. Sending Parameters to a File

❍8.2. Restoring Saved Parameters

●9. Upgrading CMS Firmware

●10. Command Reference Guide

❍10.1. Command Conventions

❍10.2. Command Response

❍10.3. Command Summary

❍10.4. Command Set

Appendices

●A. RS232 Port Interface

●B. Specifications

●C. Customer Service

List of Figures

●2.1. Instrument Front Panel

●2.2. Instrument Back Panel

●3.1. The Supervisor Level Help Screen

●3.2. The Port Status Screen (Defaults Shown)

●4.1. Terminal Block Assembly (DC Units Only)

●4.2. CMS Application Example (Not to Scale)

●5.1. Port Configuration Menu (Port 2 Shown)

●5.2. Port Parameters Menu (Modem Mode)

●5.3. Network Parameters Menu (Supervisor Mode Only)

Image 5

Western Telematic CMS-16 manual Appendices, List of Figures, Disconnecting Ports 7.1.2. Defining Hunt Groups

Contents

CMS-16 Console Management SwitchUsers Guide WTI Part No Rev. BNameplate Power Warning No Serviceable Parts Inside Authorized Service Personnel OnlyBattery Replacement Rack Mount InstallationDisconnect Power Table of Contents3.2. Apply Power to the CMS 3.3. System SetUp Ports 3.4. Connecting your PC to the CMS4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.1.2. DC Powered Units 4.2. Configure Option Switches4.2.2. Default Handshake Sw4, Sw5 4.2.3. Default Response Message Format Sw67.2. Passive Mode 7.3. Buffer Mode 7.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port Buffers 7.4. Modem Mode 8. Saving and Restoring Configuration Parameters6.2. The Port Diagnostics Screen Defaults Shown 6.1. The Port Status Screen Supervisor Mode, Defaults ShownLimited Command Access Configuration Backup2.1. Front Panel 2. Unit DescriptionTypographic Conventions COURIER FONT2.2. Back Panel 2. Power Cable Receptacle 3. Power Switch3.1. Communication Parameters Using Other Parameters for this Overview Optional3. Getting Started 3.3. System SetUp Ports 3.2. Apply Power to the CMS3.4. Connecting your PC to the CMS 3.5. Communicating with the CMS Unit2. Press Enter to access the CMS Command Mode Figure 3.1 The Supervisor Level Help Screen Figure 3.2 The Port Status Screen Defaults Shown4.1. Connecting Power to the CMS Unit 4. Hardware Installation4.1.2. DC Powered Units 4.2. Configure Option Switches4.1.1. AC Powered Units 4.2.2. Default Handshake Sw4, Sw5 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.2.4. Default Command Echo Sw7 4.3. Initialize Unit to Default Settings4.2.3. Default Response Message Format Sw6 4.5. Application Example 4.4. Connecting Devices to the CMSFigure 4.2 CMS Application Example Not to Scale 5.1. Access to the CMS Command Mode 5. Configuration$ telnet 192.1.1.1 Enter 5.2. System SetUp Ports5.3.1. The Supervisor Password 5.3. Password Functions5.3.2. The Port Passwords 5.4. Defining the Site ID and Supervisor Password5.5.1. Configuration Conventions 5.5. Port Configuration5.5.2. Port Modes 5.5.3. RS232 Port Configuration MenusTo select port parameters, proceed as follows 5. Stop Bits Default = Figure 5.2 Port Configuration Menu Modem Mode AT&C1$D2S0=15.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On Figure 5.4 IP Security Menu 5.5.5. Implementing IP SecurityExample 2 Allow access only by addresses that begin with Example 1 Deny access to all hosts except Security Mask #1Mask #1 Action Deny Security Mask #2 Mask #2 Action Permit Security Mask #1 Mask #1 Action Deny Security Mask #25.6. Copying Parameters to All Ports 6.1. The Port Status Screen /S 6. The Status Screens5.7. Save User Selected Parameters Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN Figure 6.3 The Network Status Screen Defaults Shown 6.4. The Port Parameters Screens /WWP xx Enter 7.1.1. Port Connection and Disconnection 7.1. Any-to-Any Mode7. Operation 2. Invoke the /C command to connect the desired ports D 4 Enter D 3 4 EnterD 3 Enter Hunt Group Example 7.1.2. Defining Hunt GroupsHunt Group Example 7.2. Passive Mode7.3. Buffer Mode E xx Enter 7.3.1. Reading Data from Buffer Mode PortsC xx Enter 7.3.2. Port Buffers 7.4. Modem Mode8.2. Restoring Saved Parameters 8. Saving and Restoring Configuration Parameters8.1. Sending Parameters to a File 9. Upgrading CMS Firmware 10.1. Command Conventions 10. Command Reference Guide10.2. Command Response Command Availability 10.3. Command SummaryCommand Syntax Terse Verbose1 Supervisor Mode displays parameters for all ports Enter Enter Command Mode 10.4. Command SetEnter+++Enter Resident Disconnect Sequence Format EnterxxxEnterCP Copy RS232 Port Parameters Format /C x x EnterFormat /CP Enter D Third Party DisconnectD/Y 2 Enter or /D/Y 3 Enter Format /D/Y x x EnterE Erase Buffer Format /E/Y x x EnterFormat /F Enter I Default and TestH Help Format /H EnterN Set Network Port Parameters Format /J EnterFormat /N Enter P Set RS232 Port ParametersT Reset Network Port SD Display Port DiagnosticsFormat /SD Enter SN Display Network StatusX Exit Command Mode UF Upgrade FirmwareFormat /UF Enter W Display Port Parameters WhoFormat /X Enter Appendix B. SpecificationsAppendix A. RS232 Port Interface Stop Bits 1 or Appendix C. Customer ServicePower Trademarks Used in this Manual Trademark and Copyright Information