Manuals / Western Telematic / Computer Equipment / Switch

Western Telematic CMS-16 Initialize Unit to Default Settings, Default Response Message Format Sw6

Models: CMS-16

1 62

Download 62 pages 40.13 Kb

Page 16

4.2.3.Default Response Message Format (Sw6)

Up Down XON/XOFF

Down Up Both

Up Up None

*= Factory Setting

4.2.3.Default Response Message Format (Sw6)

When commands are invoked, the CMS can respond with either verbose (English text) or terse (numeric / abbreviated) messages. Response messages are summarized in Section 10.2. After installation, the /P command can also set the response format to "none" (Quiet Mode). When Quiet Mode is selected, the unit will not send response messages.

Switch 6 Default Response Message Type

Down	Verbose (English Text) *
Up	Terse (abbreviated / numeric)

*= Factory Setting

4.2.4.Default Command Echo (Sw7)

Switch Seven enables or disables the Command Echo. When enabled, characters sent to the CMS will be echoed back to the control device.

Switch 7 Default Command Echo

Down Enable*

Up Disable

*= Factory Setting

4.3.Initialize Unit to Default Settings

If Option Switch settings are changed, new parameters will not take effect until the CMS is initialized.

Caution: After initialization, the CMS will revert to the parameters specified by the Option Switches. Any command-selected parameters will be lost.

1.Simultaneously press the SET and CLEAR buttons, located on the face of the CMS.

2.Release the CLEAR button, wait for the Port LEDs to flash, and then release the SET button.

Image 16

Western Telematic CMS-16 manual Initialize Unit to Default Settings, Default Response Message Format Sw6

Contents

Console Management Switch CMS-16Users Guide WTI Part No Rev. BNo Serviceable Parts Inside Authorized Service Personnel Only Nameplate Power WarningBattery Replacement Rack Mount InstallationTable of Contents Disconnect Power3.2. Apply Power to the CMS 3.3. System SetUp Ports 3.4. Connecting your PC to the CMS4.1.2. DC Powered Units 4.2. Configure Option Switches 4.2.1. Default Baud Rate Sw1, Sw2, Sw34.2.2. Default Handshake Sw4, Sw5 4.2.3. Default Response Message Format Sw67.1.1.2. Disconnecting Ports 7.1.2. Defining Hunt Groups 7.2. Passive Mode 7.3. Buffer Mode7.3.1. Reading Data from Buffer Mode Ports 7.3.2. Port Buffers 7.4. Modem Mode 8. Saving and Restoring Configuration Parameters6.1. The Port Status Screen Supervisor Mode, Defaults Shown 6.2. The Port Diagnostics Screen Defaults ShownLimited Command Access Configuration Backup2. Unit Description 2.1. Front PanelTypographic Conventions COURIER FONT2. Power Cable Receptacle 3. Power Switch 2.2. Back Panel3. Getting Started Using Other Parameters for this Overview Optional3.1. Communication Parameters 3.2. Apply Power to the CMS 3.3. System SetUp Ports3.4. Connecting your PC to the CMS 3.5. Communicating with the CMS Unit2. Press Enter to access the CMS Command Mode Figure 3.2 The Port Status Screen Defaults Shown Figure 3.1 The Supervisor Level Help Screen4. Hardware Installation 4.1. Connecting Power to the CMS Unit4.1.1. AC Powered Units 4.2. Configure Option Switches4.1.2. DC Powered Units 4.2.1. Default Baud Rate Sw1, Sw2, Sw3 4.2.2. Default Handshake Sw4, Sw54.2.3. Default Response Message Format Sw6 4.3. Initialize Unit to Default Settings4.2.4. Default Command Echo Sw7 4.4. Connecting Devices to the CMS 4.5. Application ExampleFigure 4.2 CMS Application Example Not to Scale 5. Configuration 5.1. Access to the CMS Command Mode5.2. System SetUp Ports $ telnet 192.1.1.1 Enter5.3. Password Functions 5.3.1. The Supervisor Password5.4. Defining the Site ID and Supervisor Password 5.3.2. The Port Passwords5.5. Port Configuration 5.5.1. Configuration Conventions5.5.3. RS232 Port Configuration Menus 5.5.2. Port ModesTo select port parameters, proceed as follows 5. Stop Bits Default = AT&C1$D2S0=1 Figure 5.2 Port Configuration Menu Modem Mode5.5.4. Network Port Configuration Menu Figure 5.3 Network Parameters Menu Supervisor Mode Only = On 5.5.5. Implementing IP Security Figure 5.4 IP Security MenuExample 1 Deny access to all hosts except Security Mask #1 Example 2 Allow access only by addresses that begin withMask #1 Action Deny Security Mask #2 Mask #2 Action Permit Security Mask #1 Mask #1 Action Deny Security Mask #25.6. Copying Parameters to All Ports 5.7. Save User Selected Parameters 6. The Status Screens6.1. The Port Status Screen /S Name The user-defined name for each port 6.2. The Port Diagnostics Screen /SD 6.3. The Network Status Screen /SN 6.4. The Port Parameters Screens /W Figure 6.3 The Network Status Screen Defaults ShownWP xx Enter 7. Operation 7.1. Any-to-Any Mode7.1.1. Port Connection and Disconnection 2. Invoke the /C command to connect the desired ports D 3 Enter D 3 4 EnterD 4 Enter 7.1.2. Defining Hunt Groups Hunt Group Example7.3. Buffer Mode 7.2. Passive ModeHunt Group Example C xx Enter 7.3.1. Reading Data from Buffer Mode PortsE xx Enter 7.4. Modem Mode 7.3.2. Port Buffers8.1. Sending Parameters to a File 8. Saving and Restoring Configuration Parameters8.2. Restoring Saved Parameters 9. Upgrading CMS Firmware 10. Command Reference Guide 10.1. Command Conventions10.2. Command Response 10.3. Command Summary Command AvailabilityCommand Syntax Terse Verbose1 Supervisor Mode displays parameters for all ports 10.4. Command Set Enter Enter Command ModeEnter+++Enter Resident Disconnect Sequence Format EnterxxxEnterFormat /C x x Enter CP Copy RS232 Port ParametersFormat /CP Enter D Third Party DisconnectFormat /D/Y x x Enter D/Y 2 Enter or /D/Y 3 EnterE Erase Buffer Format /E/Y x x EnterI Default and Test Format /F EnterH Help Format /H EnterFormat /J Enter N Set Network Port ParametersFormat /N Enter P Set RS232 Port ParametersSD Display Port Diagnostics T Reset Network PortFormat /SD Enter SN Display Network StatusUF Upgrade Firmware X Exit Command ModeFormat /UF Enter W Display Port Parameters WhoAppendix A. RS232 Port Interface Appendix B. SpecificationsFormat /X Enter Power Appendix C. Customer ServiceStop Bits 1 or Trademark and Copyright Information Trademarks Used in this Manual