Murray 309007x8B HOW to Check and Adjust the Drive Brake, HOW to Check and Adjust the Clutch

Page 26

MAINTENANCE

HOW TO CHECK AND ADJUST THE DRIVE BRAKE

Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows.

1.The location of the drive brake is on the left side of the gearbox (Figure 20).

2.Make sure the parking brake is set and the shift lever is in neutral (N). Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward.

3.Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls.

4.Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake.

WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho- rized service center.

Drive Brake

Gearbox

Hex Nut

 

Figure 20

HOW TO CHECK AND ADJUST THE CLUTCH

If the motion drive belt is loose, the clutch will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Adjust the clutch as follows.

WARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.

1.Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides.

2.Remove the cotter pin, washer, and brake spring from the adjustable nut (Figure 21).

3.Disconnect the adjustable nut from the brake lever assem- bly.

4.Align the hole in the brake lever with the rear of the slot in the frame.

5.Push the clutch rod toward the rear. Turn the adjustable nut until the nut will fit through the hole in the brake lever.

6.Assemble the adjustable nut to the brake lever and to the brake spring. Fasten with the washer and cotter pin.

7.If the belt still slips after the clutch has been adjusted, then the motion drive belt is worn or damaged and must be replaced. See “How To Replace The Motion Drive Belt”.

Cotter Pin

Brake Spring

Washer

Brake Lever

Assembly

Clutch Rod

Adjustable Nut

Figure 21

F−050611L

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents This Instruction Book Contains Information Product InformationTable of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Install the Battery Cables Maintenance Free BatteryHOW to Charge Maintenance Free Battery IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresLift Lever OperationLocation of Controls Attachments Electrical Safety SystemHOW to Operate the Ignition KEY Switch Operator Presence System SeatHOW to USE Throttle / Choke Control HOW to USE Blade Rotation ControlHOW to USE the Shift Lever See the Instruction Book for the AttachmentHOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Install the Side Discharge Attachment Secure the side discharge attachment with the fastenersCarburetor HOW to Start the EngineBefore Starting the Engine HOW to Operate with the Mower Housing HOW to Operate the Unit on HillsOperating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceFrequency Maintenance Required Comments General RecommendationsInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Check the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchHOW to Adjust the Shift Lever Connect the adjuster nut to the shifter yokeWhere to Lubricate HOW to Check the Fuel FilterHOW to Level the Mower Housing HOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelBattery HOW to Replace the FuseHOW to Clean the Mower Housing Clean the UnitTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors −050611L Repair Parts Chassis & Hood Key Description Repair PartsChassis & Hood Motion Drive Motion Drive Steering Steering Mower Housing Suspension Repair Parts Mower Housing 7601035 Complete Mower Deck Assy Wiring Harness for 30 MID−ENGINE Rider 2004 Main Harness Electrical SystemRepair Parts −050611L Index MID-ENGINE Rider Accessories
Top Page Image Contents