Weed Eater BC2500 LE, 530086828 Carton Contents, Tools Required, Attaching the Handlebar

Page 4

equipped with a spark arresting screen. If you operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arrest- ing screen will not require any service.

After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

WARNING: The muffler on this prod- uct contains chemicals known to the State of California to cause cancer.

CARTON CONTENTS

Check carton contents against the following list:

SBrushcutter

SHandlebar screws (2)

SBlade shield screws (4) S Cupped washer

S Large nut for installing blade S Long hex wrench

S Short hex wrench S Bracket cover

S Metal shield S Plastic shield

S Shoulder strap with warning S 4--point weed blade

S Trimmer head (assembled on unit) S Handlebar

S Wing nut (screwed onto shield) S Container of oil

WARNING: Always stop unit and dis- connect spark plug before performing any as- sembly procedures.

WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

TOOLS REQUIRED

S2 Hex wrenches (provided)

SAdjustable wrench or large pliers S Phillips screwdriver

ATTACHING THE HANDLEBAR

WARNING: During blade usage, the barrier portion of the handlebar must be installed as shown to provide a barrier be- tween operator and the spinning blade.

1.Locate the decal on the handlebar. This decal includes two arrows. Position the handlebar with the mounting bracket be- tween these arrows.

2.Position the bracket cover over the han- dlebar. Again make sure the handlebar is between the arrows.

3.Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the short hex wrench.

4

Screw

Handlebar

Bracket Cover

Mounting

Bracket

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments are required before starting the engine.

1.Try on shoulder strap and adjust for fit and balance before starting the engine or begin- ning a cutting operation.

2.Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoul- der.

3.Adjust the strap, allowing the hook to be about 6 inches below the waist.

4.Fasten the strap hook to the clamp located between the trigger handle and the handle- bar clamp base and lift the tool to the oper- ating position.

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions.

ASSEMBLY INFORMATION - TRIMMER HEAD

TRIMMER

HEAD

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Manual de Instrucciones Manuel d’Instructions Operator Safety Always WearUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageCarton Contents Assembly of Shoulder StrapConfiguring Your Unit Assembly Information Trimmer HeadAssembly Information Weed Blade Attaching the Plastic Shield and Trimmer HeadAttaching the Metal Shield Weed BladeInstallation of the Metal Blade ON/OFF Switch HOW to Stop Your UnitKnow Your Brushwacker Primer BulbHOW to Start Your Unit Starting a Warm EngineStarting a Flooded Engine Operating PositionTrimmer Line Advance Operating Instructions for USE with Trimmer HeadCutting Methods Operating Instructions for USE with Weed Blade Recommended Cutting PositionInspect and Clean Unit and DE- Cals Clean AIR FilterCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsBlade Replacement Carburetor AdjustmentReplacing the Line Seasonal StorageTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC Warranty Period POULAN/WEED Eater

530086828, BC2500 LE specifications

The Weed Eater 530086828, BC2500 LE is a robust and efficient tool designed for homeowners and gardening enthusiasts looking to maintain their outdoor spaces with ease. This gas-powered string trimmer features a powerful 25cc two-stroke engine, which provides ample power while being lightweight and maneuverable. With its user-friendly design, the BC2500 LE is suitable for a variety of cutting tasks, from trimming grass and weeds to edging along sidewalks and garden beds.

One of the standout features of the Weed Eater BC2500 LE is its Easy Start technology. This innovative system reduces the amount of pulling force required to start the engine, allowing users to get to work quickly without the hassle of a difficult startup process. The trimmer also boasts an adjustable speed throttle that lets users control the cutting power according to the task at hand, whether they are tackling tougher weeds or performing more delicate trimming.

The design of the BC2500 LE includes a 17-inch cutting swath, which allows for efficient coverage of larger areas while still being precise enough for detailed work. This trimmer is equipped with a dual-line bump feed head, enabling users to seamlessly extend the cutting line as needed by simply tapping the trimmer head on the ground. This feature eliminates interruptions during operation, allowing for a smooth and continuous cutting experience.

Adding to its versatility, the BC2500 LE features an ergonomic handle that reduces fatigue during extended use. The lightweight design, coupled with a balanced frame, helps users navigate around obstacles without straining their muscles. Additionally, the trimmer includes a protective shield that keeps debris at bay, ensuring a safer operation.

Another noteworthy characteristic is the durable construction of the Weed Eater BC2500 LE. Built with high-quality materials, it is designed to withstand the rigors of regular use while maintaining performance over time. The trimmer also features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance.

Overall, the Weed Eater 530086828, BC2500 LE is a reliable and efficient tool that combines power, comfort, and ease of use. Its features cater to a wide range of landscaping needs, making it an excellent choice for both novice users and experienced gardeners alike. Whether you need to maintain a tidy yard or tackle overgrown areas, the BC2500 LE stands ready to take on the challenge with reliability and efficiency.
Top Page Image Contents