Weed Eater 530086828 Attaching the Plastic Shield and Trimmer Head, Attaching the Metal Shield

Page 5

NOTE: Remove the blade and metal shield before attaching the plastic shield and trim- mer head. To remove blade, push in locking lever and hold. Rotate blade nut until the lock- ing lever falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

8.Thread trimmer head onto the shaft in the direction shown on the decal. Tighten un- til secure.

9.Release locking lever.

ASSEMBLY INFORMATION - WEED BLADE

WEED

BLADE

WARNING: The shield must be prop- erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on un- derside of shield) is sharp and can cut you.

1.Remove wing nut from shield.

2.Insert bracket into slot on shield.

3.Pivot shield until bolt passes through hole in bracket.

4.Tighten the wing nut securely.

NOTE: If your unit has a plastic cover over the threads on the threaded shaft, remove the cov- ering to expose the threads. Before installing the trimmer head, make sure the dust cup is positioned on the gearbox as shown below.

 

Bracket

Slot

Wing Nut

 

Shield Gearbox

Dust Cup

NOTE: Make sure all parts are properly installed as shown in the illustration before installing the trimmer head.

5.Push in locking lever and hold.

6.Rotate dust cup until the locking lever falls into one of the grooves.

Locking Lever

7.Continue to hold in locking lever. This will keep the shaft from turning while tighten- ing the trimmer head.

5

NOTE: Remove the trimmer head and plas- tic shield before attaching the metal shield and installing one of the weed blades. To re- move the trimmer head, push in locking lever and hold. Rotate trimmer head until the lock- ing lever falls into one of the grooves in the dust cup. Continue to hold in locking lever. This will keep the shaft from turning while loosening the cutting head. To remove the plastic shield, loosen and remove wing nut. Pivot shield to release bracket from slot. See

INSTALLATION OF THE CUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and in- structions for future use. Never use the trim- mer head with the metal blade installed.

ATTACHING THE METAL SHIELD

WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by- standers. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the tube.

1.Place the metal shield under the gearbox, and align the screw holes.

Gearbox

Shield

2.Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and secure- ly with the hex wrench provided.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Manual de Instrucciones Manuel d’Instructions Always Wear Operator SafetyFuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageAssembly of Shoulder Strap Carton ContentsConfiguring Your Unit Assembly Information Trimmer HeadAttaching the Plastic Shield and Trimmer Head Assembly Information Weed BladeAttaching the Metal Shield Weed BladeInstallation of the Metal Blade HOW to Stop Your Unit ON/OFF SwitchKnow Your Brushwacker Primer BulbStarting a Warm Engine HOW to Start Your UnitStarting a Flooded Engine Operating PositionCutting Methods Operating Instructions for USE with Trimmer HeadTrimmer Line Advance Recommended Cutting Position Operating Instructions for USE with Weed BladeClean AIR Filter Inspect and Clean Unit and DE- CalsCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsCarburetor Adjustment Blade ReplacementReplacing the Line Seasonal StorageTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC POULAN/WEED Eater Warranty Period

530086828, BC2500 LE specifications

The Weed Eater 530086828, BC2500 LE is a robust and efficient tool designed for homeowners and gardening enthusiasts looking to maintain their outdoor spaces with ease. This gas-powered string trimmer features a powerful 25cc two-stroke engine, which provides ample power while being lightweight and maneuverable. With its user-friendly design, the BC2500 LE is suitable for a variety of cutting tasks, from trimming grass and weeds to edging along sidewalks and garden beds.

One of the standout features of the Weed Eater BC2500 LE is its Easy Start technology. This innovative system reduces the amount of pulling force required to start the engine, allowing users to get to work quickly without the hassle of a difficult startup process. The trimmer also boasts an adjustable speed throttle that lets users control the cutting power according to the task at hand, whether they are tackling tougher weeds or performing more delicate trimming.

The design of the BC2500 LE includes a 17-inch cutting swath, which allows for efficient coverage of larger areas while still being precise enough for detailed work. This trimmer is equipped with a dual-line bump feed head, enabling users to seamlessly extend the cutting line as needed by simply tapping the trimmer head on the ground. This feature eliminates interruptions during operation, allowing for a smooth and continuous cutting experience.

Adding to its versatility, the BC2500 LE features an ergonomic handle that reduces fatigue during extended use. The lightweight design, coupled with a balanced frame, helps users navigate around obstacles without straining their muscles. Additionally, the trimmer includes a protective shield that keeps debris at bay, ensuring a safer operation.

Another noteworthy characteristic is the durable construction of the Weed Eater BC2500 LE. Built with high-quality materials, it is designed to withstand the rigors of regular use while maintaining performance over time. The trimmer also features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance.

Overall, the Weed Eater 530086828, BC2500 LE is a reliable and efficient tool that combines power, comfort, and ease of use. Its features cater to a wide range of landscaping needs, making it an excellent choice for both novice users and experienced gardeners alike. Whether you need to maintain a tidy yard or tackle overgrown areas, the BC2500 LE stands ready to take on the challenge with reliability and efficiency.
Top Page Image Contents