HOW to Stop Your Unit, HOW to Start Your Unit

oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before stor- age for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor clean- er products in the fuel tank or permanent dam- age may occur. See the STORAGE section for additional information.

HELPFUL TIP

If your engine switch reads “push to stop”, it is always in the ON position.

HOW TO STOP YOUR UNIT

STo stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

SIf engine does not stop, move choke to the FULL CHOKE position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Primer Bulb

Choke

Lever

Starter Handle

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger.

NOTE: If engine dies with the choke le- ver in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 6 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

FX26S, 545137264 specifications

The Weed Eater 545137264, FX26S is a versatile and robust string trimmer designed to meet the demands of both residential and professional users. This powerful tool is engineered for efficiency, precision, and comfort, making it an essential addition to any landscaping arsenal.

One of the standout features of the FX26S is its reliable 26cc 2-cycle engine. This engine balances power with fuel efficiency, enabling users to tackle dense grass and overgrown weeds with ease. The trimmer’s high-speed rotation allows for swift cutting capabilities, ensuring a clean and precise finish to any garden area. Additionally, the engine is designed to offer easier starting, reducing frustration for users and allowing for more time spent on the task at hand.

The FX26S also incorporates a lightweight design, weighing in at just under 10 pounds. This feature enhances user maneuverability, letting operators navigate around tight corners and intricate flower beds without strain. The adjustable D-handle and shoulder strap provide extra comfort and balance, further enhancing user experience during prolonged use.

Equipped with an innovative dual-line cutting system, the Weed Eater FX26S allows for a wider cutting swath, maximizing efficiency. The automatic line feed ensures that the trimmer maintains optimal line length, reducing downtime for line adjustments. This ergonomic approach to design makes it well-suited for tackling larger areas without continuous interruptions.

One of the technological highlights of the FX26S is its anti-vibration system. This feature minimizes hand fatigue, making it feasible to work for longer periods without discomfort. The trimmer is also easy to assemble and disassemble, facilitating quick storage and transportation.

The Weed Eater 545137264, FX26S is built with durability in mind. Its sturdy construction and quality materials ensure that the unit can withstand the rigors of frequent use, whether for residential yard work or professional landscaping. Furthermore, the trimmer is supported by a reliable warranty, providing peace of mind for users.

In summary, the Weed Eater 545137264, FX26S supports a combination of power, comfort, and innovative features. Its efficient engine, lightweight design, dual-line system, and anti-vibration technology contribute to a user-friendly experience that enhances productivity in lawn care tasks. This trimmer is an excellent choice for anyone looking to maintain a pristine yard or tackle tough landscaping jobs.