Siemens S7-300F-2 PN, DP manual 507

Page 43

Industry Automation and Drive Technologies - SCE

Variable									Description

		Setting the MOBY Operating

			Value
			Value				Operating Mode
							Operating Mode

					Default

IM Type

-; reserved for setting with switch or GSD parameterization: different interfaces without switch under- stand under MOBY mode = 0 the MOBY I_mode.

	MOBY I or MOBY E (without MDS			All
	507)
MOBY I with MDS 507

	MOBY U/D or RF300 – without multi tag handling

	Res. for MOBY U – with multi tag handling
	Reserved for MOBY D or RF300 - with multi tag
	handling (FB55)

MOBY F with MDS F1xx
	MOBY F with MDS F4xx
	MOBY F (reserved for MDS

To be noted:

MOBY_mode must only be changed after an IM is switched on

Scannung_time is the scanning time for the MDS 507 of MOBY I and MOBY V. For all other MDS types, the value 00 can be used.here. The figure below shows the setting for the scanning time (refer also to configguration manual for Reader 44/MDS 507):

Time value:00-3F

Time factor

Example: The result of a scanning time of 1 second = 81 hex for the parameter ABTA (scanning time)

Notes

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

TIA Training Document	Page 43 of 65
Module E11
Status: 01/2010	Radio Frequency Identification (RFID) with SIMATIC S7-300F-2PN/DP and
RF180C

Image 43

Contents Industry Automation and Drive Technologies SCE Module E11Industry Automation and Drive Technologies SCE Preface Page Objective S7’Prerequisites Simatic RF180C ASM Industry Automation and Drive Technologies SCE CPU Rfid Fundamentals DB47 Data structure of the German language UDTs is as followsPage Industry Automation and Drive Technologies SCE Page Industry Automation and Drive Technologies SCE Industry Automation and Drive Technologies SCE Value range for the address of the gateway router Industry Automation and Drive Technologies SCE MAC addressValue range for the IP address Value range for the subnet screen formIndustry Automation and Drive Technologies SCE Industry Automation and Drive Technologies SCE Industry Automation and Drive Technologies SCE Page Page Page Save and close DB48 Generating DB48 Open DB48, set up 1024 bytesGenerating DB49 Open DB49 and insert UDT261 and UDT271 Page Generating DB50 Open DB50 and insert UDT111 and UDT281 Save and close DB50 Generate DB47 Open DB47 and add UDT21 for each request Save and close DB47 DB45, UDT11 is called for each reader Generating DB45 Open DB45 and insert UDT11 for each readerData view of DB45 to byte DB47 request data block is referred to in DB45Save and close DB45 Page Generating Function FC11 Set up in variables Set up OUT variablesSave and close FC11 Reading data from the transponder Data View of the UDT21 Command OverviewCommand Writing data to the transponderRead out Reader status Command NextCommand END Initialize TransponderTransponder Status Switching the reader aerial on/offExample of a command string in DB47 Data view of the UDT11 Variable Description Parameter commandDBaddress Value = 50 for Reader2 507 Industry Automation and Drive Technologies SCE ISO MDS Page Page Industry Automation and Drive Technologies SCE Variable Description Control bits from Bit8 to Bit15Moby U/D or RF300 Generating FB10 Then, set up in variables Next, set up OUT variablesReader block Network 1 Command start Network 2 Reset Reader Industry Automation and Drive Technologies SCE Networks 4 to Page Task Supplementing the symbol tableGenerating FB1 Industry Automation and Drive Technologies SCE FB10 is inserted as a multi-instance block Industry Automation and Drive Technologies SCE Network Industry Automation and Drive Technologies SCE Network 4 to Page Open OB1 and call FB1 with DB1 Page Page Industry Automation and Drive Technologies SCE Symbol Table