Electrolux AG22H42STA manual Tractor

Page 19

TRACTOR

Always observe safety rules when per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your trac- tor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with trailing edge up towards deck as

shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Trailing Edge

Blade

 

 

Mandrel

 

2

Assembly

Up

Center

01

14

 

 

 

Flat

Hole

 

 

 

Washer

 

 

 

 

Lock

 

 

 

 

Washer

 

 

 

Star

Blade Bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharp- ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a

5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

01202

Blade

5/8” Bolt or Pin

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and termi- nals can cause the battery to “leak” power.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Lawn Tractor Warranty Table of ContentsGeneral Operation Safety RulesII. Slope Operation III. Children IV. ServiceDo not Safety Rules Customer Responsibilities Product SpecificationsAPI-SG-SL Steering Wheel Unassembled PartsTo Remove Tractor from Carton ASSEMBLY/PRE-OPERATIONTools Required for Assembly HOW to SET UP Your TractorInstall Seat Install Mulcher PlateCheck Deck Levelness To Convert to Bagging or DischargingAssemble Gauge Wheels to Mower Deck Check Tire PressureOperation Know Your Tractor Height Adjustment Knob Used toTo USE Choke Control HOW to USE Your TractorTo Operate on Hills To Operate MowerTo Start Engine Before Starting the EnginePurge Transmission Mulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication Chart MaintenanceBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidAIR Filter CleaningTo Install Mower Service and AdjustmentsTo Remove Mower To Replace Mower Blade Drive Belt To Level Mower HousingSIDE-TO-SIDE Adjustment Belt InstallationTo Replace Motion Drive Belt To Check and Adjust BrakeTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Transmission Removal ReplacementTo Replace Headlight Bulb Replacing BatteryTo Adjust Throttle Control Cable To Adjust CarburetorStorage BatteryOther Problem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

AG22H42STA specifications

The Electrolux AG22H42STA is an innovative and versatile appliance designed for modern households, offering a blend of power, efficiency, and convenience. This upright vacuum cleaner is engineered to handle a variety of surfaces, making it an ideal choice for both carpets and hard floors.

One of the standout features of the Electrolux AG22H42STA is its powerful motor, providing robust suction capabilities that effectively lift dirt, dust, and pet hair from deep within carpets and upholstery. This ensures a thorough clean, making it particularly suitable for homes with pets or heavy foot traffic.

The vacuum's multi-surface cleaning technology is another highlight, allowing users to transition seamlessly from carpets to hard floors without needing to change attachments. This adaptability makes the AG22H42STA a practical solution for maintaining a clean home, regardless of the flooring types present.

Ergonomics has been a key focus in the design of the AG22H42STA. Its lightweight structure and easy maneuverability reduce strain on the user, making cleaning less of a chore. Additionally, it features a comfortable handle and convenient controls that enable quick adjustments on the go, enhancing the user experience.

Another noteworthy characteristic is the vacuum's advanced filtration system, which captures allergens and fine dust particles, contributing to improved indoor air quality. This is particularly beneficial for allergy sufferers, as it minimizes the presence of environmental irritants.

The AG22H42STA is designed for user convenience, featuring a large-capacity dust container that reduces the frequency of emptying and maintenance. Moreover, the bagless design streamlines cleaning, making it easier to dispose of collected debris.

In terms of aesthetics, the vacuum’s sleek, modern look integrates well into any home setting. The design not only emphasizes functionality but also aesthetics, making it a stylish addition to cleaning arsenal.

Overall, the Electrolux AG22H42STA embodies a commitment to high performance, reliability, and user-friendly features, making it a noteworthy option for anyone seeking an efficient cleaning solution. Whether tackling messes on carpets or hard surfaces, this vacuum is engineered to meet the demands of today’s busy lifestyles while providing a high level of cleanliness.
Top Page Image Contents