Electrolux AG22H42STA manual Replacing Battery, To Replace Headlight Bulb, Interlocks and Relays

Page 26

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

02614

Weak or Dead Battery Fully Charged Battery

REPLACING BATTERY

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected

first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to neg- ative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely.

8.Close terminal access doors.

9.Close hood.

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

Headlight Wire

Connector

01536

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, see eingine manual.

Keps Nut

Terminal

Access

Door

Terminal

Guard

Hex Bolt

Positive

(Red) Cable

Negative

(Black) Cable

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor des need adjustment, see engine manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Lawn Tractor Table of Contents WarrantyII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SG-SL Product SpecificationsCustomer Responsibilities Unassembled Parts Steering WheelHOW to SET UP Your Tractor ASSEMBLY/PRE-OPERATIONTools Required for Assembly To Remove Tractor from CartonInstall Mulcher Plate Install SeatCheck Tire Pressure To Convert to Bagging or DischargingAssemble Gauge Wheels to Mower Deck Check Deck LevelnessOperation Height Adjustment Knob Used to Know Your TractorHOW to USE Your Tractor To USE Choke ControlTo Operate Mower To Operate on HillsBefore Starting the Engine To Start EnginePurge Transmission Mowing Tips Mulching Mowing TipsBefore Each USE MaintenanceGeneral Recommendations Lubrication Chart Tractor Transaxle Pump Fluid EngineTransaxle Cooling BeltsCleaning AIR FilterTo Remove Mower Service and AdjustmentsTo Install Mower Belt Installation To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Check Brake To Check and Adjust BrakeTo Adjust Brake To Replace Motion Drive BeltTransmission Removal Replacement Transaxle Motion Control LE- VER Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Replacing BatteryTo Adjust Throttle Control Cable To Replace Headlight BulbOther BatteryStorage Troubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

AG22H42STA specifications

The Electrolux AG22H42STA is an innovative and versatile appliance designed for modern households, offering a blend of power, efficiency, and convenience. This upright vacuum cleaner is engineered to handle a variety of surfaces, making it an ideal choice for both carpets and hard floors.

One of the standout features of the Electrolux AG22H42STA is its powerful motor, providing robust suction capabilities that effectively lift dirt, dust, and pet hair from deep within carpets and upholstery. This ensures a thorough clean, making it particularly suitable for homes with pets or heavy foot traffic.

The vacuum's multi-surface cleaning technology is another highlight, allowing users to transition seamlessly from carpets to hard floors without needing to change attachments. This adaptability makes the AG22H42STA a practical solution for maintaining a clean home, regardless of the flooring types present.

Ergonomics has been a key focus in the design of the AG22H42STA. Its lightweight structure and easy maneuverability reduce strain on the user, making cleaning less of a chore. Additionally, it features a comfortable handle and convenient controls that enable quick adjustments on the go, enhancing the user experience.

Another noteworthy characteristic is the vacuum's advanced filtration system, which captures allergens and fine dust particles, contributing to improved indoor air quality. This is particularly beneficial for allergy sufferers, as it minimizes the presence of environmental irritants.

The AG22H42STA is designed for user convenience, featuring a large-capacity dust container that reduces the frequency of emptying and maintenance. Moreover, the bagless design streamlines cleaning, making it easier to dispose of collected debris.

In terms of aesthetics, the vacuum’s sleek, modern look integrates well into any home setting. The design not only emphasizes functionality but also aesthetics, making it a stylish addition to cleaning arsenal.

Overall, the Electrolux AG22H42STA embodies a commitment to high performance, reliability, and user-friendly features, making it a noteworthy option for anyone seeking an efficient cleaning solution. Whether tackling messes on carpets or hard surfaces, this vacuum is engineered to meet the demands of today’s busy lifestyles while providing a high level of cleanliness.
Top Page Image Contents