Electrolux AG22H42STA manual Transaxle Motion Control LE- VER Neutral Adjustment

Page 25

Engine Pulley

Clutching Idler

Stationary Idler

Center Span

Keeper

Transmission

Input Pulley

01510

TRANSAXLE MOTION CONTROL LE- VER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.

Loosen adjustment bolt in front of the

 

right rear wheel, and lightly tighten.

2.

Start engine and move motion con-

 

trol lever until tractor does not move

 

forward or backward.

3.

Hold motion control lever in that posi-

 

tion and turn engine off.

4.

While holding motion control lever in

 

place, loosen the adjustment bolt.

5.

Move motion control lever to the neu-

 

tral (N) (lock gate) position.

6.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed

to get to adjustment bolt, move mower

deck height to the lowest position.

After above adjustment is made, if the

tractor still creeps forward or backward

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact our authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from an authorized ser- vice center/department. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

while motion control lever is in neutral

position, follow these steps:

1.

Loosen the adjustment bolt.

2.

Move the motion control lever 1/4 to

 

1/2 inch in the direction it is trying to

Axle

Cover

Square Key

00663

 

creep.

3.

Tighten adjustment bolt securely.

4.

Start engine and test.

5.

If tractor still creeps, repeat above

 

steps until satisfied.

Motion Control

Neutral

Lever

Lock Gate

 

 

Adjustment

02239

Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before op- erating the tractor. See “PURGE TRANS- MISSION” in the Operation section of this manual.

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT- TERY

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Lawn Tractor Warranty Table of ContentsGeneral Operation Safety RulesII. Slope Operation III. Children IV. ServiceDo not Safety Rules Customer Responsibilities Product SpecificationsAPI-SG-SL Steering Wheel Unassembled PartsTools Required for Assembly ASSEMBLY/PRE-OPERATIONHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat Install Mulcher PlateAssemble Gauge Wheels to Mower Deck To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor Height Adjustment Knob Used toTo USE Choke Control HOW to USE Your TractorTo Operate on Hills To Operate MowerTo Start Engine Before Starting the EnginePurge Transmission Mulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication Chart MaintenanceBefore Each USE Tractor Transaxle Cooling EngineTransaxle Pump Fluid BeltsAIR Filter CleaningTo Install Mower Service and AdjustmentsTo Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingBelt Installation To Replace Mower Blade Drive BeltTo Adjust Brake To Check and Adjust BrakeTo Check Brake To Replace Motion Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control LE- VER Neutral AdjustmentTransmission Removal Replacement Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable Replacing BatteryTo Adjust Carburetor To Replace Headlight BulbStorage BatteryOther Problem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

AG22H42STA specifications

The Electrolux AG22H42STA is an innovative and versatile appliance designed for modern households, offering a blend of power, efficiency, and convenience. This upright vacuum cleaner is engineered to handle a variety of surfaces, making it an ideal choice for both carpets and hard floors.

One of the standout features of the Electrolux AG22H42STA is its powerful motor, providing robust suction capabilities that effectively lift dirt, dust, and pet hair from deep within carpets and upholstery. This ensures a thorough clean, making it particularly suitable for homes with pets or heavy foot traffic.

The vacuum's multi-surface cleaning technology is another highlight, allowing users to transition seamlessly from carpets to hard floors without needing to change attachments. This adaptability makes the AG22H42STA a practical solution for maintaining a clean home, regardless of the flooring types present.

Ergonomics has been a key focus in the design of the AG22H42STA. Its lightweight structure and easy maneuverability reduce strain on the user, making cleaning less of a chore. Additionally, it features a comfortable handle and convenient controls that enable quick adjustments on the go, enhancing the user experience.

Another noteworthy characteristic is the vacuum's advanced filtration system, which captures allergens and fine dust particles, contributing to improved indoor air quality. This is particularly beneficial for allergy sufferers, as it minimizes the presence of environmental irritants.

The AG22H42STA is designed for user convenience, featuring a large-capacity dust container that reduces the frequency of emptying and maintenance. Moreover, the bagless design streamlines cleaning, making it easier to dispose of collected debris.

In terms of aesthetics, the vacuum’s sleek, modern look integrates well into any home setting. The design not only emphasizes functionality but also aesthetics, making it a stylish addition to cleaning arsenal.

Overall, the Electrolux AG22H42STA embodies a commitment to high performance, reliability, and user-friendly features, making it a noteworthy option for anyone seeking an efficient cleaning solution. Whether tackling messes on carpets or hard surfaces, this vacuum is engineered to meet the demands of today’s busy lifestyles while providing a high level of cleanliness.
Top Page Image Contents