Craftsman 316.2927 manual Troubleshooting, Problem Cause Remedy

Page 13

TROUBLESHOOTING

Problem

 

Cause

 

Remedy

 

 

 

 

 

Engine fails to start

1.

Spark plug wire disconnected.

1.

Connect wire to spark plug.

 

2.

Ignition switch is OFF (O).

2.

Turn switch to ON (I).

 

3.

Fuel tank empty or stale fuel.

3.

Fill tank with clean, fresh gasoline.

 

4.

Primer bulb wasn’t pressed enough.

4. Press primer bulb fully and slowly 5-7

 

 

 

 

times.

 

5.

Engine flooded.

5.

Use starting procedure with choke lever

 

 

 

 

in the Open (C) position.

 

6.

Faulty spark plug.

6.

Clean, adjust gap, or replace.

Engine flooded

1.

Too much gasoline primed through

1.

With the choke lever in the Open (C)

 

 

engine.

 

position.

 

 

 

2.

Squeeze the throttle control to the wide

 

 

 

 

open position.

 

 

 

3.

Place right foot on the right side of

 

 

 

 

cultivator wheel.

 

 

 

4.

Pull the starter rope briskly 3 to 5 times

 

 

 

 

or until engine starts.

 

 

 

5.

With tines off the ground, depress the

 

 

 

 

throttle lever against the upper handle

 

 

 

 

to increase engine speed and rotate

 

 

 

 

tines.

Engine runs erratic

1.

Spark plug wire loose.

1.

Connect and tighten spark plug wire.

 

2.

Blocked fuel line or stale fuel.

2.

Clean fuel line; fill tank with clean, fresh

 

 

 

 

gasoline

 

3.

Vent in gas cap plugged.

3.

Clear vent.

 

4.

Water or dirt in fuel system.

4.

Drain fuel tank. Refill with fresh fuel.

 

5.

Dirty air filter.

5.

Clean or replace air filter.

 

6.

Carburetor out of adjustment.

6.

See qualified service center.

Engine overheats

1.

Engine oil level low.

1.

Fill crankcase with proper oil.

 

2.

Dirty air filter.

2.

Clean or replace air filter.

 

3.

Carburetor not adjusted properly.

3.

See qualified service center.

Occasional skip (hesitates)

1.

Spark plug gap too close.

1.

Adjust gap to .025”.

at high speed

 

 

 

 

Idles poorly

1.

Spark plug fouled, faulty or gap too

1.

Reset gap to .025” or replace spark

 

 

wide.

 

plug.

 

2.

Carburetor improperly adjusted.

2.

See qualified service center.

 

3.

Dirty air filter.

3.

Clean or replace air filter.

NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Sears service center or other qualified service center or call 1-800-4-MY-HOME®.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Cultivator / Edger Warranty Table of ContentsTraining SafetyMaintenance And Storage Setting Up Your Cultivator / Edger Disconnecting Spark PlugAssembly Removing Unit From CartonOperation Stopping EngineGas Fill-Up Oil Fill-UpStarting Engine Adjusting the Wheel Support Bracket Using Your CultivatorAttaching the Edger Wheel And Blade Checking Oil MaintenanceChanging Oil Carburetor Adjustment Air Filter MaintenanceSpark Arrestor Maintenance Replacing The Spark PlugThen every 50 hours of operation thereafter Service and Storage Tine Removal and ReplacementStoring Your Cultivator / Edger Problem Cause Remedy TroubleshootingParts List Part Description 28 31 2933 5045 Short Block 5-13, 15, 16, 71-83 Owner’s Warranty Responsibilities Emission Warranty StatementManufacturer’s Warranty Coverage Garantía ÍndiceEsta garantía no cubre Seguridad CapacitaciónMantenimiento y almacenamiento FuncionamientoLas responsabilidades De la garantía del Dueño Como Declaración de Garantía de EmisiónLa cobertura De la garantía del Fabricante Parties Lâches dans Carton Configuración de su cultivadora / bordeadoraDesconexión De La Bujía MontajeInterruptor encendido / apagado FuncionamientoLlenado de aceite Detención del motorLlenado de nafta Encendido del motorAjuste de la ménsula de soporte de la rueda Utilización de su cultivadoraConexión de la rueda y de la cuchilla de la bordeadora Mantenimiento Cambio de aceiteAjuste del carburador Mantenimiento del filtro de aireReemplazo de la bujía Mantenimiento del dispositivo contra chispasDespacho de aduana de Balancín Balancines Ajuste Servicio Y Almacenamiento Almacenamiento de la cultivadora / bordeadoraProblema Causa Solución Solución DE ProblemasPage

316.2927 specifications

The Craftsman 316.2927 is a versatile power tool that has gained popularity among DIY enthusiasts and professionals alike. It stands out in the Craftsman lineup, known for its durability, reliable performance, and user-friendly design. This tool is primarily recognized as a powerful drill, making it an essential addition to any toolbox.

One of the main features of the Craftsman 316.2927 is its high-performance motor. This motor enables the drill to deliver up to 20 volts of power, providing sufficient torque for a variety of applications such as drilling into wood, metal, and plastic. The enhanced power makes it suitable for both light and heavy-duty tasks, catering to users' needs across different projects.

Another notable characteristic is the adjustable speed settings. The Craftsman 316.2927 comes with a variable speed feature, allowing users to choose the right speed for their specific tasks. With speeds ranging from 0 to 1,500 RPM, it accommodates both precision drilling and rapid driving, giving users exceptional control over their work. In addition, the drill features a reversible function, making it easy to switch between drilling and removing screws effortlessly.

Ergonomics play a vital role in user satisfaction, and the Craftsman 316.2927 excels in this regard. It is designed with a comfortable grip, reducing hand fatigue during prolonged use. The lightweight construction further enhances its usability, ensuring that even extended projects can be tackled without excessive strain.

Furthermore, the Craftsman 316.2927 incorporates advanced battery technology. It employs lithium-ion batteries, which provide a longer lifespan and quicker charging times compared to traditional NiCad batteries. Users can enjoy extended working periods without the worry of downtime due to obsolete battery performance.

The design of the Craftsman 316.2927 includes bright LED lights that illuminate the work area, ensuring precision in low-light conditions. This feature is particularly beneficial for users conducting tasks in dim environments, enhancing visibility and safety.

In summary, the Craftsman 316.2927 is a feature-rich drill that appeals to a wide range of users. With its powerful motor, adjustable speed settings, ergonomic design, advanced battery technology, and integrated LED lights, it delivers impressive performance and convenience for various drilling tasks. Whether for home improvement projects or professional use, the Craftsman 316.2927 proves to be a reliable choice for enhancing productivity and efficiency.
Top Page Image Contents