Craftsman 316.2927 manual Then every 50 hours of operation thereafter

Page 11

and then every 50 hours of operation thereafter.

IMPORTANT: The engine must be cold when checking or adjusting the valve clearance. This task should be performed inside in a clean and dust free area. A new gasket must be used in this adjustment. A new rocker arm gasket (part # 791-182099)can be purchased from your Sears service center.

•Remove the muffler cover by pressing down on the corner with a flat blade screwdriver. Slide the notches on the sides of the muffler cover over the tabs on the engine cover and remove.

•Remove the two screws on top of the engine cover with a phillips screwdriver. See Figure 13.

 

Screw

Engine Cover

Remove Screws

 

 

Muffler

Figure 13

•Remove the screw on back of the engine cover. See Figure 13.

•Disconnect the spark plug wire and clean dirt around plug. Remove the spark plug from the cylin- der head by turning a 5/8” socket counterclockwise.

•Remover engine cover.

NOTE: Pull the starter rope out a little to give some slack and to ease the removal of the engine cover.

•Clean dirt from around the rocker arm cover and remove the screw holding the rocker arm cover with a large flat blade screwdriver or Torx T25 bit.

See Figure 14.

Rocker Arm Cover

Spark Plug Hole

Figure 14

•Remove the rocker arm cover and gasket.

Pull the starter rope slowly to bring the piston to the top of its travel. Make sure:

•The piston should be at the top of its travel while looking in the spark plug hole. See Figure 14.

•Both rocker arms should move freely and both valves are closed.

If not, repeat this step.

•Slide the feeler gauge between the rocker arm and

the valve return spring. Measure the clearance between the valve stem and rocker arm. Do both intake and exhaust valves. See Figure 15.

The recommended clearance for both intake and exhaust is .003-.006” (.076-.152mm). Use a standard (.127mm) feeler gauge. The feeler gauge should slide between the rocker arm and valve stem with a slight amount of resistance without binding.

Rocker Arms

Adjusting Nuts

 

Gasket

Feeler Gauge

 

 

Adjusting Nut

 

Rocker Arm

.003-.006

 

(.076-.152mm)

 

 

Feeler Gauge

Figure 15

If the clearance is not within specification:

•Turn the adjusting nut using a 5/16” (8mm) wrench or nut driver.

•To increase clearance, turn the adjusting nut counterclockwise.

•To decrease clearance, turn the adjusting nut clockwise.

•Recheck both clearances and adjust as necessary.

•Reinstall the rocker arm cover using a new gasket. Torque the screw to 20-30in-lb (2.2-3.4 Nm).

•Reinstall the engine cover and check alignment of the cover before tightening the screws.

•Replace the muffler cover and slip the long tabs on the cover into the engine cover. Slide the notches on the side of muffler cover over the tabs on engine cover. Snap into place.

•Check spark plug, reinstall, and attach spark plug wire.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Cultivator / Edger Warranty Table of ContentsTraining SafetyMaintenance And Storage Removing Unit From Carton Disconnecting Spark PlugSetting Up Your Cultivator / Edger AssemblyOperation Stopping EngineStarting Engine Oil Fill-UpGas Fill-Up Attaching the Edger Wheel And Blade Using Your CultivatorAdjusting the Wheel Support Bracket Changing Oil MaintenanceChecking Oil Replacing The Spark Plug Air Filter MaintenanceCarburetor Adjustment Spark Arrestor MaintenanceThen every 50 hours of operation thereafter Storing Your Cultivator / Edger Tine Removal and ReplacementService and Storage Problem Cause Remedy TroubleshootingParts List Part Description 28 31 2933 5045 Short Block 5-13, 15, 16, 71-83 Manufacturer’s Warranty Coverage Emission Warranty StatementOwner’s Warranty Responsibilities Esta garantía no cubre ÍndiceGarantía Seguridad CapacitaciónMantenimiento y almacenamiento FuncionamientoLa cobertura De la garantía del Fabricante Declaración de Garantía de EmisiónLas responsabilidades De la garantía del Dueño Como Montaje Configuración de su cultivadora / bordeadoraParties Lâches dans Carton Desconexión De La BujíaInterruptor encendido / apagado FuncionamientoEncendido del motor Detención del motorLlenado de aceite Llenado de naftaAjuste de la ménsula de soporte de la rueda Utilización de su cultivadoraConexión de la rueda y de la cuchilla de la bordeadora Mantenimiento Cambio de aceiteMantenimiento del dispositivo contra chispas Mantenimiento del filtro de aireAjuste del carburador Reemplazo de la bujíaDespacho de aduana de Balancín Balancines Ajuste Servicio Y Almacenamiento Almacenamiento de la cultivadora / bordeadoraProblema Causa Solución Solución DE ProblemasPage

316.2927 specifications

The Craftsman 316.2927 is a versatile power tool that has gained popularity among DIY enthusiasts and professionals alike. It stands out in the Craftsman lineup, known for its durability, reliable performance, and user-friendly design. This tool is primarily recognized as a powerful drill, making it an essential addition to any toolbox.

One of the main features of the Craftsman 316.2927 is its high-performance motor. This motor enables the drill to deliver up to 20 volts of power, providing sufficient torque for a variety of applications such as drilling into wood, metal, and plastic. The enhanced power makes it suitable for both light and heavy-duty tasks, catering to users' needs across different projects.

Another notable characteristic is the adjustable speed settings. The Craftsman 316.2927 comes with a variable speed feature, allowing users to choose the right speed for their specific tasks. With speeds ranging from 0 to 1,500 RPM, it accommodates both precision drilling and rapid driving, giving users exceptional control over their work. In addition, the drill features a reversible function, making it easy to switch between drilling and removing screws effortlessly.

Ergonomics play a vital role in user satisfaction, and the Craftsman 316.2927 excels in this regard. It is designed with a comfortable grip, reducing hand fatigue during prolonged use. The lightweight construction further enhances its usability, ensuring that even extended projects can be tackled without excessive strain.

Furthermore, the Craftsman 316.2927 incorporates advanced battery technology. It employs lithium-ion batteries, which provide a longer lifespan and quicker charging times compared to traditional NiCad batteries. Users can enjoy extended working periods without the worry of downtime due to obsolete battery performance.

The design of the Craftsman 316.2927 includes bright LED lights that illuminate the work area, ensuring precision in low-light conditions. This feature is particularly beneficial for users conducting tasks in dim environments, enhancing visibility and safety.

In summary, the Craftsman 316.2927 is a feature-rich drill that appeals to a wide range of users. With its powerful motor, adjustable speed settings, ergonomic design, advanced battery technology, and integrated LED lights, it delivers impressive performance and convenience for various drilling tasks. Whether for home improvement projects or professional use, the Craftsman 316.2927 proves to be a reliable choice for enhancing productivity and efficiency.
Top Page Image Contents