Craftsman 316.2927 manual Maintenance And Storage

Page 4

operation. Stop machine if anyone enters the area.

5.Be careful when cultivating in hard ground. The tines may catch in the ground and propel the cultivator forward. If this occurs, let go of the handle and do not restrain the machine.

6.Never operate the machine at high transport speeds on hard or slippery surfaces.

7.Exercise caution to avoid slipping or falling.

8.Look down, behind, and use care when pulling machine towards you.

9.Start the engine according to the instructions found in this manual and keep feet well away from the tines at all times.

10.After striking a foreign object, stop the engine, disconnect the spark plug wire and ground against the engine. Thoroughly inspect the machine for any damage. Repair the damage before starting and operating.

11.Disengage all clutch and stop engine before you leave the operating position (behind the handle). Wait until the tines come to a complete stop before unclogging the tines, making any adjustments, or inspections.

12.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

13.Muffler and engine become hot and can cause a burn. Do not touch.

14.Use caution when cultivating near fences, buildings and underground utilities. Rotating tines can cause property damage or personal injury.

15.Do not overload machine capacity by attempting to cultivate soil to deep or to fast of a rate.

16.If the machine should start making an unusual noise or vibration, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.

17.Keep all shields, guards and safety devices in place and operating properly.

18.Never pick up or carry machine while the engine is running.

19.Use only attachments and accessories available by the Sears. Failure to do so, can result in personal injury.

20.If situations occur which are not covered in this manual, use care and good judgment. Contact your nearest Sears service center.

Maintenance And Storage

1.Never tamper with safety devices. Check their proper operation regularly.

2.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.

3.Before cleaning, repairing, or inspecting, stop the engine and make certain the tines and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

4.Do not change the engine governor settings or over-speed the engine. The governor controls the maximum safe operating speed of the engine.

5.Maintain or replace safety and instruction labels, as necessary.

6.Follow this manual for safe loading, unloading, transporting, and storage of this machine.

7.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc.

8.Always refer to the operator’s manual for proper instructions on off-season storage.

9.Always store unit in cultivator mode (all four tines on unit) to avoid tip over.

10.If the fuel tank has to be drained, do this outdoors.

11.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

WARNING: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Cultivator / Edger Table of Contents WarrantySafety TrainingMaintenance And Storage Disconnecting Spark Plug Setting Up Your Cultivator / EdgerAssembly Removing Unit From CartonStopping Engine OperationGas Fill-Up Oil Fill-UpStarting Engine Adjusting the Wheel Support Bracket Using Your CultivatorAttaching the Edger Wheel And Blade Checking Oil MaintenanceChanging Oil Air Filter Maintenance Carburetor AdjustmentSpark Arrestor Maintenance Replacing The Spark PlugThen every 50 hours of operation thereafter Service and Storage Tine Removal and ReplacementStoring Your Cultivator / Edger Troubleshooting Problem Cause RemedyParts List Part Description 28 31 2933 5045 Short Block 5-13, 15, 16, 71-83 Owner’s Warranty Responsibilities Emission Warranty StatementManufacturer’s Warranty Coverage Garantía ÍndiceEsta garantía no cubre Capacitación SeguridadFuncionamiento Mantenimiento y almacenamientoLas responsabilidades De la garantía del Dueño Como Declaración de Garantía de EmisiónLa cobertura De la garantía del Fabricante Configuración de su cultivadora / bordeadora Parties Lâches dans CartonDesconexión De La Bujía MontajeFuncionamiento Interruptor encendido / apagadoDetención del motor Llenado de aceiteLlenado de nafta Encendido del motorUtilización de su cultivadora Ajuste de la ménsula de soporte de la ruedaConexión de la rueda y de la cuchilla de la bordeadora Cambio de aceite MantenimientoMantenimiento del filtro de aire Ajuste del carburadorReemplazo de la bujía Mantenimiento del dispositivo contra chispasDespacho de aduana de Balancín Balancines Ajuste Almacenamiento de la cultivadora / bordeadora Servicio Y AlmacenamientoSolución DE Problemas Problema Causa SoluciónPage

316.2927 specifications

The Craftsman 316.2927 is a versatile power tool that has gained popularity among DIY enthusiasts and professionals alike. It stands out in the Craftsman lineup, known for its durability, reliable performance, and user-friendly design. This tool is primarily recognized as a powerful drill, making it an essential addition to any toolbox.

One of the main features of the Craftsman 316.2927 is its high-performance motor. This motor enables the drill to deliver up to 20 volts of power, providing sufficient torque for a variety of applications such as drilling into wood, metal, and plastic. The enhanced power makes it suitable for both light and heavy-duty tasks, catering to users' needs across different projects.

Another notable characteristic is the adjustable speed settings. The Craftsman 316.2927 comes with a variable speed feature, allowing users to choose the right speed for their specific tasks. With speeds ranging from 0 to 1,500 RPM, it accommodates both precision drilling and rapid driving, giving users exceptional control over their work. In addition, the drill features a reversible function, making it easy to switch between drilling and removing screws effortlessly.

Ergonomics play a vital role in user satisfaction, and the Craftsman 316.2927 excels in this regard. It is designed with a comfortable grip, reducing hand fatigue during prolonged use. The lightweight construction further enhances its usability, ensuring that even extended projects can be tackled without excessive strain.

Furthermore, the Craftsman 316.2927 incorporates advanced battery technology. It employs lithium-ion batteries, which provide a longer lifespan and quicker charging times compared to traditional NiCad batteries. Users can enjoy extended working periods without the worry of downtime due to obsolete battery performance.

The design of the Craftsman 316.2927 includes bright LED lights that illuminate the work area, ensuring precision in low-light conditions. This feature is particularly beneficial for users conducting tasks in dim environments, enhancing visibility and safety.

In summary, the Craftsman 316.2927 is a feature-rich drill that appeals to a wide range of users. With its powerful motor, adjustable speed settings, ergonomic design, advanced battery technology, and integrated LED lights, it delivers impressive performance and convenience for various drilling tasks. Whether for home improvement projects or professional use, the Craftsman 316.2927 proves to be a reliable choice for enhancing productivity and efficiency.
Top Page Image Contents