Craftsman 247.79452 Starting Engine, Stopping Engine, Raising and Lowering Beam, Control

Page 11

•Make sure the spark plug wire is disconnected. Prime the pump by pulling the recoil starter as far as it will go. Repeat approximately 10 times.

•Reconnect the spark plug wire and start engine.

•Use the control handle to engage the wedge to the far extended position. Refer to Figure 7. Retract the wedge.

•Fill tank to within 1-1/2" to 2" from the top of the tank.

Fill hydraulic fluid here

Reservoir

Tank

Reservo_irVent

Plug

Figure 8

•Extend and retract the wedge 12 complete cycles to remove trapped air in the system (system is "self-bleeding").

•Refill the reservoir to within 1-1/2" to 2" from the

top of the tank. Much of the originalfluid has been drawn intothe cylinder and hoses. Make certain to refill the reservoir to prevent extreme damage to the hydraulic pump.

NOTE; Some fluidmay overflow from the ventplug as

the system builds heat and the fluid expands and seeks a balanced level.

Move control handle BACK or UP to return the wedge. See Figure 7.

Starting Engine

•Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle (rope will pull slightlyharder at this point). Let the rope rewind slowly.

•Pull rope with a rapid, continuous,full arm stroke. Keep a firm gdp on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter.

•Repeat preceding two instructions until engine fires. When engine starts, move choke lever on engine halfway to Half Choke position and then gradually to No Choke position.

•If engine falters, move choke lever to Half Choke until engine runs smoothly and then move it to No Choke position.

•Run wedge up and down beam 6 to 8 times to circulate the hydraulic fluid, which will warm and thin the fluid.

Stopping Engine

•Move throttle control lever to STOP position.

•Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended.

Raising and Lowering Beam

•Place log splitter on a firm, level surface. To raise the beam for vertical operation, pull out the beam lock on the tongue and pivot it down to release the beam.

•Move the beam to the verticalposition. Secure it with the beam lock on the reservoirtank assembly. See Figure 10,

•Attach spark plug wire and rubber boot to spark plug. See Figure 9,

•Place the throttle control lever in FAST position. See Figure 6 and Figure 9,

•Move choke lever to FULL CHOKE position,

A_ach spark

Beam Lock

Raise beam assembly

in this direction

/

Horizontal Beam Lock

Move choke

lever tc

/

Move throttle

rope

control

Figure 9

Figure 10

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Log Splitter Spark Plug Gap Champion Model NumberEspanbl DexronInjury to Yourself or others TowingTraining To the rules for safe operation This ManualOtherwise not alert to use your log splitter PreparationOperation Important Information Customer ResponsibilitiesTailight Kit NeverUnpacking from Crate Disconnecting Spark PlugSetting Up Log Splitter Tools and Other Items RequiredSpring Lever Jack Stand Final AssemblyBeam Assembly Tire PressureMeets Ansi Safety Requirements Reservoir Fill-Up Engine bore damage due to inadequate lubricationControl Starting EngineStopping Engine Raising and Lowering BeamOperating the Log Splitter Transporting the Log SplitterOperating Position Before Each UseBeam And Splitting Wedge General RecommendationsHydraulic Fluid Hex Bolt Engine MaintenanceFlexible Pump Coupling TiresCarburetor Engine SpeedNut LockWasher HexStart the engine and let it run until the fuel lines LOG SplitterProblem Possible Cause Corrective Action Will not splitlogs Or repairs beyond the minor adjustments listed aboveEngine failsto start Dirty air cleaner Not in on position82 ?8 Craftsman 9 H.P. Log Splitter ModelB627 333 Craftsman 9 H.P, Log Splitter Model 173 35377 Governor Lever Clamp 650880151 127 Valve Cover204 35881 Air Cleaner FilterAir Cleaner Cover 2o3Carburetor IncL 184 of Engine 631970640109 632164Key Part No KeySears

247.79452 specifications

The Craftsman 247.79452 is a versatile and efficient snow blower designed to tackle the toughest winter conditions. It is an ideal choice for homeowners looking to maintain their driveways, sidewalks, and outdoor spaces free from heavy snowfall. This powerful machine blends user-friendly features with advanced technology to provide a reliable snow-clearing solution.

One of the standout features of the Craftsman 247.79452 is its robust 24-inch clearing width, allowing users to quickly and effectively clear large areas with each pass. The 208cc engine offers impressive power, enabling it to handle wet, heavy snow with ease, making it suitable for a variety of snowfall conditions. The electric start technology further enhances convenience, allowing users to start the machine effortlessly with the push of a button, sparing them from the hassle of pulling cords in cold weather.

The snow blower is equipped with a 2-stage system that efficiently lifts snow and discharges it through a chute. The adjustable chute allows for a 180-degree rotation, giving users the flexibility to direct snow away from driveways and pathways, preventing unnecessary buildup. This feature is particularly beneficial for homeowners with large driveways or those living in areas that receive significant snowfall.

Another notable characteristic is its self-propelled capability, which helps users navigate through deep snow without excessive effort. The Craftsman 247.79452 offers multiple speed settings, allowing for both forward and reverse motion, making it easier to maneuver in tight spaces and around obstacles.

Durability is a key aspect of the Craftsman brand, and the 247.79452 is no exception. Built with high-quality materials, this snow blower is designed to withstand the rigors of winter use while providing long-lasting performance. The heavy-duty auger and impeller are engineered for optimal snow clearing, minimizing the risk of clogging even in challenging conditions.

In conclusion, the Craftsman 247.79452 snow blower combines power, convenience, and durability to make snow removal a much simpler task. Its innovative features, such as the electric start, self-propelled capability, and adjustable chute, provide users with a reliable instrument for managing winter storms. With the Craftsman 247.79452 in your arsenal, you can confidently tackle whatever Mother Nature throws your way.
Top Page Image Contents