To SET Parking Brake, Stopping Mower Blades

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles, or stan- dard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

•Depress clutch/brake pedal into full "BRAKE" position and hold.

• Place parking brake lever in .......

"ENGAGED" position and release pres- sure from clutch/brake pedal. Pedal should remain in "BRAKE" position. Make sure parking brake will hold trac- tor secure.

	Push-In to	Attachment Clutch
Throttle		Attachment Clutch
Throttle		Switch Pull Out To
Control

Turn ignition key to =OFF" position and

remove key. Always remove key when leaving tractor to prevent unauthorized

use.

•Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than =OFP will cause

the battery to be discharged (dead). NOTE: Under certain conditions when tractor is standing idle with the engine run- ning, hot engine exhaust gases may cause =browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

_, CAUTION: Always stop tractor com- pletely, as described above, before leaving the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL Always operate engine at full throttle.

•Operating engine at less than full throt-

tle reduces the battery charging rate.

TO USE CHOKE CONTROL

Lever

Parking Brake

Pedal =Drive" Position

PositionPosition

STOPPING

MOWER BLADES -

•To stop_mower blades, move attach- ment clutch switch to "DISENGAGED" position.

GROUND DRIVE -

•To stopground drive, depress clutch/brake pedal into full "BRAKE"

IpOsition. .

•Move motion control lever to neutral (N) position.

IMPORTANT: The motion control lever does not retum to neutral (N) position when the clutch/brake pedal is depressed.

ENGINE -

•Move throttle control to slow position. NOTE:. Failure to move throttle control to slow position and allowing engine to idle

before stopping may cause engine to =backfire".

Use choke control whenever you are start- ing a cold engine. Do not use to start a warm engine.

•To engage choke control, pull knob out.

Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the motion control lever.

•Start tractor with motion control lever in neutral (N) position.

•Release parking brake and clutch/brake pedal.

•Slowly move motion control lever to

desired position.

TO ADJUST MOWER CUTTING HEIGHT

The cutting height is controlled by turn-

ing the height adjustment knob in desired direction.

•Turn knob clockwise (C) to raise cutting height..

•/urn Knoo counterclockwise (O)to lower cutting height.

The cutting height range is approximately 1-1/2" to 4-1/2". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending up.onsoil conditions, height of grass and

14 types of grass being mowed.

917.27306 specifications

The Craftsman 917.27306 is a standout lawn mower known for its reliability, performance, and advanced features. This gas-powered, walk-behind mower is designed for homeowners who demand quality and efficiency in their lawn care routine.

One of the main features of the Craftsman 917.27306 is its powerful 163cc engine. This reliable engine provides adequate cutting power for various grass types, ensuring a clean and even cut. The mower's performance is bolstered by a self-propelling mechanism that makes it easier to maneuver across different terrains, particularly on slopes and uneven surfaces. This feature significantly reduces user fatigue, allowing for a more enjoyable mowing experience.

The Craftsman 917.27306 is equipped with a 21-inch cutting deck, which strikes a balance between maneuverability and cutting width. This size makes it suitable for medium to large yards, enabling homeowners to cover ground quickly while still being able to navigate tight spaces with ease. Additionally, the cutting deck has a height adjustment feature, allowing users to customize their mowing height. This takes into account different grass types and desired lawn aesthetics.

The mower also incorporates advanced mulching technology, which finely chops grass clippings and returns them to the lawn as a natural fertilizer. This not only nourishes the grass but also eliminates the need for bagging clippings, promoting a healthier lawn ecosystem. Furthermore, the Craftsman 917.27306 includes a rear bagging option for those who prefer a clean-cut lawn or want to collect clippings for disposal.

Another notable characteristic is the ergonomic handle design, which is adjustable to suit different user heights. This thoughtful feature ensures comfort during operation, reducing strain and making the mowing process less labor-intensive.

Safety is a priority with the Craftsman 917.27306, as it is designed with a blade brake system that halts the blades when the user releases the handle. This provides peace of mind, especially for families with children or pets.

In summary, the Craftsman 917.27306 is a reliable and feature-rich lawn mower that caters to the needs of homeowners. Its powerful engine, self-propelling design, adjustable cutting height, and efficient mulching system make it an ideal choice for maintaining a beautiful lawn with minimal effort. With its combination of performance, technology, and user-friendly features, the Craftsman 917.27306 stands out as an excellent investment for lawn care enthusiasts.