Craftsman 917.376541 owner manual HOW to USE Your Lawn Mower

Page 8

The operation of any lawn SAFETVG'ASSESmower can result in foreign

objects thrown into the eyes, which can result in severe

eye damage. Always wear safety glasses or eye shields while oper- ating your lawn mower or performing any adjustments or repairs. We recommend a standard safety glasses orwide vision safety mask worn over spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

Engine speed was set at the factory for optimum performance. It is not adjustable.

ENGINE ZONE CONTROL

_k,CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the

risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

•Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

DRIVE CONTROL

. Self-propelling is controlled by holding the operator presence control bar down to the handle and pulling either drive control lever rearward to the handle. The further toward the handle a lever is pulled, the faster the unit will travel.

. Forward motion will stop when either the operator presence control bar or a drive control lever are released. To stop forward motion without stopping engine, release a drive control lever only. Hold operator presence control bar down against handle to continue mowing without self-propelling.

handle to lift the front wheels off the ground while turning lawn mower.

DRIVE CONTROL ADJUSTMENT

Over time, the drive control system may become "loose", resulting in decreased speed. There is a turnbuckle on the drive

control housing to increase tension on the drive cable. Proceed as follows:

1.Turn unit off and disconnect spark plug wire from spark plug.

2.Rotate turnbuckle on drive control to increase drive speed.

3.Operate mower to test drive speed. Readjust as required.

4.If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be replaced.

ustment

turnbuckle

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit

your requirements. Medium position is best for most lawns.

• To change cutting height, pull up on adjuster lever, move wheel up or down to suit your requirements and release adjuster lever. Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when lever inserts into hole in plate.

LEVER BACKWARD

TO LOWER MOWER

NOTE: If after releasing the drive control the mower will not roll backwards, push

LEVER FORWARD

Lever

the mower forward slightly to disengage drive wheels.

Operator presence control bar

Drive control levers

TO ENGAGE DRIVE CONTROL

DRIVE CONTROL DISENGAGED

TO RAISE MOWER

Plate

• To keep drive control engaged

when

8

turning corners, push down on

the

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Craftsman Yearfull Warranty on Craftsman Lawn Mower Your Safety is InvolvedDo not General OperationIV. Safe Handling of Gasoline Service GeneralSAE NGK BPR6ESLawn Mower Maintenance Lawn Mower PerformanceNOW to SET UP Your Mower To Remove Mower from CartonTo Unfold Handle To Assemble Grass CatcherMeets Cpsc Safety Requirements Know Your Lawn MowerHOW to USE Your Lawn Mower Rear Bagging Side DischargingFor Rear Bagging To Convert MowerBefore Starting Engine Mulching Mowing TiPS Lubrication Chart General RecommendationsBefore Each USE LubricationLawn Mower Drive WheelsGrass Catcher Gear CaseEngine To Change Engine OILCleaning Water Washout FeatureClean Under Drive Cover MufflerTo Adjust Handle Lawn MowerRear Deflector To Remove Drive BeltLawn Mower CarburetorHandle FoldProblem Cause OtherFuel System Engine OILProblem CauseCorrection Need More HELP?Sears, Roebuck and Co., Hoffman Estates, IL SU Seguridad Esta ComprometidaOperacion III. NinosII. Operacion Sobre LAS Cuestas HacerAPI SG-SL SAE NGK BPR6ESServicio de Instalaci6n Sears Rendimiento DE LA SegadoraMantenimiento DE LA Segadora Como Preparar SU Segadora Producto. Aprenda y comprenda sus significados Cumple CON LOS Requisitos DE Seguridad DE LA CpscControl DE LA Impulsion Como Usar SU SegadoraVelocidad DEL Motor Para Convertir LA Segadora Segadoras CON Descarga TraseraSegadoras CON Descarga Lateral Para Ensacamiento TraseroAntes DE Hacer Arrancar EL MotorPara Hacer Arrancar EL Motor ImportanteOnsejos Para Segar ApagadoOFF Consejos Para Segar Y ACOL- CharRecomendaciones Generales Antes DE Cada USOLubricacion Tabla DE LubricacionSegadora Recogedor DE Cosped Caja DE EngranajesMotor Para Cambiar EL Aceite DEL MotorLimpieza PRECAUCI6NDerrubio DEL Agua Limpie Debajo DE LA Cubierta DE LA ImpulsionPara Ajustar LA Altura DE Corte Desviador TraseroPara Remover Correa DE Impulsion Para Ajustar EL MangoDe la emJsJ6n, los cuales sean hechos al costo CarburadorMango SegarOtros Problema CausaCilindro Problema CausaCraftsman Rotary Lawn Mower - Model Number KEY Part DescriptionKEY Part Description GCV160-LAS3ACraftsman Rotary Lawn Mower - Model Number KEY PartModel Number GCV160-LAS3A Honda 4-CYCLE EngineLabel Labels Muffler OIL PAN Service Notes Service Notes Need More HELP? Your Home
Top Page Image Contents