Craftsman 917.289071, 917.289072, 917.289070 Check Engine OIL Level, ADD Gasoline, To Start Engine

Page 15

BEFORESTARTINGTHE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

1.Check engine oil with tractor on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsertthe dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FUL[L'mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See the oil viscosity chart inthe Maintenance section of this manual).

To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

*Fill fuel tank to bottom of filler neck. Do not

overfill. Usefresh, clean, regutar unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30 days to ensure fuel freshness.

_kCAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: When operating in tempera- tures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can

attract moisture which leads to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or longer. Drain the gas

tank, start the engine and let it run until the fuel linesand carburetorare empty. Usefresh

fuel next season. See Storage Instructions for additional information. Never use engine

orcarburetor cleaner products in the fuel tank or permanent damage may occur.

3.Move attachment clutch to disengaged position.

4.Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below.

5.Insert key into ignition and turn key clockwise to start position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50°F/10°C and above)

6.When engine starts, move the throttle control to the fast position.

*The attachments and ground drive can now be used. If the engine does not accept the toad, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50°F/10°C and below)

6.When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, immedi- ately move the throttle control to the fast position. Engine warm-up may take from several seconds to several

minutes (the colder the temperature, the longer the warm-up).

*The attachments can also be used dur- ing the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F) the carburetor fuel mixture may need to be adjusted for best engine performance (see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual).

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1.Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

2.Place gear shift lever in neutral (N)

position.15

Image 15
Contents Craftsman TWO Years on Riding Equipment Craftsman Full WarrantyGeneral Operation IV. Towing Service Safe Handling of GasomneGeneralservice U1R Sears Installation ServiceAPI-SG-SL RC12YCTo Remove Tractor from Carton Unpack Carton Tools Required for AssemblyInstall Seat To Check BatteryAttach Steering Wheel Assemble Extension Shaft and Boot Install Steering WheelCheck for Proper Position To Adjust SeatTo Roll Tractor OFF Skid Check Deck Levelness@@@@ Tractor Know Your TractorGround Drive HOW to USE Your Tractor To SET Parking BrakeStopping Mower BladesTo Operate Mower To Adjust Mower Cutting HeightTo Adjust Gauge Wheels To Move Forward BA Ckwa RDMents Reverse Operation System ROSCheck Engine OIL Level ADD GasolineTo Start Engine Mowing TiPS General Recommendations MaintenanceLubrication Chart Schedule USE Sours .OURS Sours HoursTires Presence SystemSystem ROS LUBRiCATiON Transaxle MaintenanceBatte RY =BELTSMuffler Engine OIL FilterAIR Filter Engine Cooling SystemService or Adjustments To iNSTALL MowerTo Remove Mower 03042rex To Level Mower Visual SIDE=TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Precision SIDE=TO=SIDE AdjustmentTo Replace Motion Drive Belt Belt InstallationTo Replace Mower Blade Drive Belt Belt RemovalTral Adjustment To Adjust Throttle Control Replacing BatteryEngine OIL Fuel SystemCause Correction ProblemWill not start Engine will notEngine Will not Start Loss of powerRun when Operator Mower blades will not rotatePSI Loss Engine dies when tractor is shiftedLLI OgSDOS Aios Para EL Equipo Tractor Garantja Completa DE CraftsmanFuncionamiento General DvertenciaServicio Manipulacion Segura DE LA Gasolina IV, RemolqueEstando Servicio DE Instalacion Sears Asiento Volante de direcci6nInstalacion DEL Volante DE Direccion Herramientas Necesarias ParaEL Montaje Antes DE Remover EL Tractor DE LA CorrederaPara Ajustar EL Asiento Instalacion DEL AsientoREVISI6N DE LA Posicion Adecuada DE Todas LAS Correas FLISTA DE RevisionREVISI6N DE LA PRESI6N DE LAS Llantas Revision DE LA Nivelacion DEL ConjuntoEstrangu Pido Lento Lacion DE EmbragueAccesorio DEL Famimaricese CON SU Tractor Enganchar Desenganchado IMPULSI6N DE Recorrido Como Usar SU TractorPara Ajustar EL Freno DE ESTACIONA= Miento Parada Cuchillas DE LA SegadoraPara Operar LA Segadora Para Moverse Hacia Adelante Y Hacia AtrasPara Ajustar LA Altura DE Corte DE LA Segadora Para Ajustar LAS Ruedas CALIBRA- DorasPara Transportar Funcionamiento ATR.&SUsar EL Sistema DE Funcionamiento Atras Para Operar EN CerrosPara Hacer Arrancar EL Motor Antes DE Hacer Arrancar ELMotor Revise EL Nivel DE Aceite DEL Motor Agregue GasomnaConsejos Para Segar Manteniimiento Recomendaciones GeneralesAntes DE Cada USO Programa DEFunoionamiento ATR/S ROS TractorOPERAOI6N DEL Freno LlantasPara Cambiar EL Aoeite DEL Motor Enfriamjento DEL TransejeCorreas Motor LubrioaoionFiltro DE Combustible EN Linea LimpiezaSistema DE Enfriamiento DE Aire SilenciadorFije LOS Brazos DE Suspension Vicio O DE Hacer AjustesPara Desmontar LA Cortadora Instale LA Segadora03042tex Ajuste DE Delante a ATR,S Para Njvelar LA SegadoraRegulacion Visual DE Lado a Lado Regulacion DE LA Precision DE LadoDesmontaje DE LA Correa Para Cambiar LA Correa DE IMPULSI6N DE LA Cuchilla SegadoraRemocion DE LA Correa Instalacion DE LA CorreaParaadj Untar LOS CAB LES DE EM Palm E Impreskn / Inclinackn DE LAS Ruedas DelanterasPara Remover LAS Ruedas Para Hacer Reparaciones Motor Motor Sistema DE Combustible Aoeite DEL MotorOtros TOR Identificacion DE ProblemasHaoer Arrancar EL MO ChokeSears IDENTIFICACI6N DE ProblemasProblema Causa CorreccionApaga Problema Causa CorreccionGao MaHage home

917.289071, 917.289070, 917.28907, 917.289072 specifications

The Craftsman 917.28907, 917.289071, 917.289070, and 917.289072 represent a series of high-performance lawn mowers designed to tackle various yard maintenance tasks with efficiency and ease. Each model in this lineup features a powerful engine combined with user-friendly technologies, making them ideal for homeowners seeking reliability and robust performance in their lawn care equipment.

One of the standout features of these mowers is their cutting deck design. With a wide 42-inch deck, the Craftsman series enables users to cover more ground in less time, ensuring a neat and professionally looking lawn. The deck is constructed from durable materials, designed to withstand regular use while maintaining sharpness for effective cutting.

The mowers are powered by dependable gasoline engines that provide consistent performance and are built to handle various terrains. The powerful engines ensure that even tougher jobs, such as mowing overgrown grass, are completed without difficulty. Furthermore, these models are equipped with electric start capabilities, allowing for easy starting with the turn of a key, eliminating the hassle of traditional pull-start systems.

Another noteworthy technology found within these models is the adjustable cutting height feature, which allows users to customize the mow height according to their lawn type and seasonal needs. This versatility is crucial for maintaining a healthy lawn and achieving the desired aesthetic appeal.

Ergonomically designed, these mowers prioritize user comfort and ease of handling. Features such as padded handles contribute to a more comfortable grip while mowing, reducing strain during extended use. Additionally, the models are designed with maneuverability in mind, making them easy to navigate around obstacles like trees, flower beds, and other landscaping features.

The Craftsman 917.28907 series models also emphasize maintenance convenience. They come equipped with a rear discharge, which effectively disperses grass clippings behind the mower, resulting in a neat finish without the need for additional cleanup. The side-mounted bagging system further enhances lawn care, allowing for efficient grass collection.

In summary, the Craftsman 917.28907, 917.289071, 917.289070, and 917.289072 lawn mowers are engineered for durability, ease of use, and efficiency. With powerful engines, versatile cutting options, and user-centric design features, these mowers stand out as exemplary solutions for homeowners looking to maintain beautiful and healthy lawns with minimal effort.