Craftsman 917.28914 owner manual Blade Care

Page 17

TRACTOR

Always observe safety rules when performing

any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced° (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See the sides of tires for proper PSi).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damager

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly° tf

your tractor does not function as described, repair the problem immediately.

The engine should not start unless the

brake pedal is fully depressed, and the attachment clutch control is in the disem

gaged position.

CHECK OPERATOR PRESENCE

SYSTEM

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the at- tachment clutch is engaged, any attempt

by the operator to leave the seat should shut off the engine.

The attachment clutch should never oper- ate unless the operator is in the seat,

CHECK REVERSE OPERATION (ROS) SYSTEM

When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt

by the operator to drive in reverse should shut off the engine,

,When the engine is runningwith the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in reverse should NOT shut off the engine_

BLADE CARE

For best results mower blades must be sharp° Replace worn, bent or damaged blades.

,_ CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty_

BLADE REMOVAL

't. Raise mower to highest position to allow access to blades_

NOTE: Protect your hands with gloves and/ or wrap blade with heavy cloth.

2.Remove blade bolt by turning counter- clockwise.

3.Install new blade with stamped "GRASS

SIDE" facing the ground.

IMPORTANT; To ensure proper assembly, center hole in blade must align with star on mandrel assembly,

4.Install and tighten blade bolt securely (45-55 Ft. Lbs, torque).

IMPORTANT: Special blade bolt is heat treated°

 

Star

Center Hole

\

Blade Bolt

Mandrel

(Special) _-_-

Assembly

 

Blade

ROS "ON" Position Engine "ON" Position (Normal Operating)

17

Image 17
Contents Sears Craftsman Help Line Lawn TractoSears, Roebuck and Co., Hoffman Estates, IL Craftsman Full Warranty TWO Years on Riding EquipmentGeneral Operation Following safety instructions could resultRII, Children Service Safe Handling of GasolineGeneral Service Repair Protection ProductCustomer Responsibilities To Remove Tractor from Carton Unpack Carton To Check BatteryCheck Tire Pressure ChecklistCheck Deck Levelness Check Brake System@@@@ Know Your Tractor Stopping Mower Blades HOW to USE Your Tractor To SET Parking BrakeGround Drive EngineTo Adjust Gauge Wheels To Adjust Mower Cutting HeightTo Move Forward BackwardMents ADD Gasoline Before Starting the Engine Check Engine OIL LevelTo Start Engine Automatic Transmission Warm UPMowing Tips Purge TransmissionSchedule ChartOuRs Ou.s HouRS General RecommendationsBlade Care Transaxle Cooling BatteryTransaxle Pump Fluid BeltsEngine Cooling System Clean AIR ScreenMuffler Spark PlugsDeck Washout Port CleaningCution To Remove Mower Service or AdjustmentsTo Install Mower O3042tox Precision SIDE-TO-SIDE Adjustment Visual SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Level MowerBelt Removal Belt InstallationTo Check Brake Front Wheel TOE.IN/CAMBERTo Remove Wheel for Repairs Transaxle Motion Control Lever Neutral AdjustmentTo Attach ,JUMPER Cables To Remove CABLES, Reverse OrderTo Remove Hood & Grillassembly 1. Raise hood Replacing BatteryTo Adjust Throttle Control Interlocks and RelaysEngine OIL Engine Fuel SystemCylinders OtherLardto start ProblemCorrection Engine PowerWill Excessive VibrationPoor cut uneven Cutting2 ProblemCausecorrection Problem Cause Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationDOS Aiios Para EL Equipo Tractor GARANTiA Completa DE CraftsmanFuncionamiento General IV.REMOLQUE Perdertracci6n PonersiempreunamarchacuandoseestPage DEL Producto ESPECtFICACIONESRCI 2YC Responsabilidades DEL ClienteEL Montaje Herramientas Necesarias ParaDesempaque LA Caja DE Carton Antes DE Remover EL Tractor DE LA CorrederaRevision DE LA Nivelacion DEL CON Junto Revision DE LA Presion DE LASLlantas @@e SU Tractor Familiaricese CON SU TractorImpulsion DE Recorrido ParadaMotor Para Usar EL Control DE LA AcelerPara Ajustar LA Altura DE Corte DE LA Segadora Para Moverse Hacia Adelante Y Hacia ATR/SPara Ajustar LAS Ruedas Calibra DorasTRANSMIStON Enganchada Para TransportarTransmision Desenganchada Remolque DE Carretillas O Otros ACCESOR!OSAutomatica Para Hacer Arrancar EL MotorConsejos Para Segar Purgar LA TRANSMISI6NMantenimiento ProgramadeRecomendaciones Generales Antes DE Cada USOBATERiA TractorREMOCt6N DE LA Cuchilla Nivel DEL Fluido DE LA Bomba DEL Transeje Enfriamiento DEL TransejeCorreas Motor LubricacionSilenciador Sistema DE Enfriamiento DE AireSuJiAS LimpiezaPuerto DE Lavado DE LA Cubierta Fije LOS Brazos DE Suspension Para Desmontar LA CortadoraInstale LA Segadora Page Ajuste DE Delante a Atras Para Nivelar LA SegadoraPara Reemplazar LA COR REA DE Trans Para Cambiar LA Correa DE Impulsion DE LA Cuchilla SegadoraPara Remover LAS Ruedas Para Hacer Reparaciones Si el tractorLas Delantera Reemplazar LA BateriaPara Cambiar EL Fusible ¥ DEL EnrejadoAceite DEL Motor Sistema DE CombustibleDrene el aceite con et motor caliente y c&mbielo CilindrosVe.ar!a secci6n apropiadae n el manual a menosque Identificacion DE ProblemasCausa 1DENTIFICACION DE ProblemasEst dirigido a un centro de servicio Vea ta secci6n apropiada en el manual a menos que SearsPage Grados MAX Canada MY-HOMEOur Home

917.28914 specifications

The Craftsman 917.28914 is a versatile lawn mower that stands out in the crowded market of outdoor power equipment. Renowned for its reliability and performance, this machine is designed to make lawn maintenance easier and more efficient for homeowners and gardening enthusiasts alike.

One of the key features of the Craftsman 917.28914 is its powerful 21-inch cutting deck, which allows users to cover a larger area in less time. The cutting height is adjustable, enabling users to tailor their mowing experience to the specific needs of their lawn, whether they prefer a closer cut or a higher one for a lush, healthy turf. The deck is constructed from durable steel, ensuring longevity and resilience against wear and tear from various terrain types.

Powered by a robust 140cc engine, the Craftsman 917.28914 delivers reliable performance that can handle thick grass and tough mowing conditions. Its easy-starting system ensures that users can get to work quickly without the frustration often associated with starting gas-powered mowers. This mower also integrates a self-propulsion technology, making it easier to navigate through uneven landscapes. This feature significantly reduces physical exertion, allowing users to mow larger areas without feeling fatigued.

Another notable characteristic is the mower's bagging system which efficiently collects clippings, reducing the need for additional clean-up after mowing. The rear discharge capability provides an alternative for users who prefer to leave clippings on the lawn to decompose and enrich the soil.

In terms of user comfort, the Craftsman 917.28914 includes ergonomic handles that reduce strain and vibration during operation. The lightweight design also contributes to ease of maneuverability, making it convenient to operate in tight spaces and around obstacles.

Overall, the Craftsman 917.28914 combines advanced technology with practical features to deliver a lawn mower that meets the demands of various users. Whether you're a seasoned gardener or a newcomer to lawn care, this mower promises to enhance your mowing experience with its efficiency, performance, and thoughtful design. With Craftsman’s reputation for quality and innovation, the 917.28914 is a reliable choice for maintaining a beautiful and healthy lawn.