Craftsman 917.273322 owner manual To Replaceheadlightbulb, Interlocksandrelays, To Replacefuse

Page 29

TO REPLACEHEADLIGHTBULB

\

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

Headlight Wire

Connector

INTERLOCKSANDRELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACEFUSE

Replace with 30 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO ADJUST ATTACHMENT LIFT SPRING

•While holding spring bushing with wrench, loosen jam nut.

•Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments.

•Turn adjustment bolt counterclockwise for lighter attachments.

•Retighten jam nut against spring bushing.

IMPORTANT: Do not adjust for maxi- mum spring tension when using _ight attachments such as a mower. Adjust lift lever spring to aid in lifting attachment. Do not overpower spring. When remov- ing attachment, always adjust spring tension to its lowest position.

(/__J Adjustment Bolt

pring Bushing

ENGINE

Maintenance, repair, or replacement of the emission control devices and

systems, which are being done at the customers expense, may be performed by any non-road engine repair establish ment or individual. Warranty repairs mus be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not b_ necessary. Check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttl_ control lever to fast position.

•Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw. Tighten clamp screw securely.

Idle Fuel Adjusting Idle speed Adjusting Needle

 

_ntLift

Throtth

_,

:, _, Spring

Centre

Cable

Jam Nut

TO REMOVE HOODAND GRILL

ASSEMBLY

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

Stop

 

Screw

Screw

Clamp

29

Choke Control Cabh

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Sears Craftsman Help Line Pro, Mon Sat £RAFTZMIIN+Limited 90 DAY Warranty on Battery Limited TWO Year Warranty on Craftsman Riding EquipmentSEARS, Roebuckand CO., D/817 WA, Hoffman ESTATES, IL General OperationChildren ServiceDo not Be alert and turn machine off if children enter the areaNever run a machine inside a closed area TION!!! Become AWARE!!! Your Safety is InvolvedMaintenance Agreement Product SpecificationsRead and observe the safety rules BafierySteering Wheel Unpack Carton Tools Required for AssemblyTo Remove Tractor from Installseat HOW to SET UP Your TractorCheck Battery Before Removing Tractor from SkidTo Attach Nose Roller To Drive Tractor OFF SkidSee Operation section for location Function of controls Brackets to Mower DeckUse Pliers For LoopBracket Check Tire Pressure Check Brake SystemCheck Mower Levelness First time. Follow proper startingH L Attachment Lift Lever Used to Know Your TractorBwltcn To SET Parking Brake HOW to USE Your TractorTo Adjust Mower Cutting Make all turns slowly To Adjust Gauge WheelsTo Operate Mower To Transport To Start EngineTowing Carts and Other Attachments Before Starting the Engine Check Engine OIL LevelAutomatic Transmission Warm UP Purge TransmissionMowing Tips Before Each USE Lubrication ChartGeneral Recommendations Blade Removal Always observe safety rules whenOperator Presence System Engine BatteryTransaxle Pump Fluid LubricationTo Service PRE-CLEANER Clean AIR INTAKE/COOLING AreasAIR Filter Engine OIL FilterTo Level Mower Housing To Install MowerSIDE-TO-SIDE Adjustment Tractor To Remove MowerMower Drive Belt Installation FRONT-TO-BACK Adjustment Important Deck Must be LevelTo Replace Mower Drive Belt Mower Drive Belt RemovalTo Replace Mower Blade Drive Belt Install Mower and Drive BeltTo Adjust Attachment Clutch Belt Installation To Adjust BrakeNylon Locknut Brake To Replace Motion Drive BeltTo Adjust Steering Wheel Alignment To Adjust Motion Control LeverFront Wheel TOE-IN Adjustment Transmission REMOVAL/REPLACE- MentTo Remove Wheel for Repairs Front Wheel To Start Engine with a Weak BatteryReplacing Battery To Replaceheadlightbulb To Adjust Attachment Lift SpringInterlocksandrelays To ReplacefuseTo Adjust Carburetor To Adjust Choke ControlPreliminary Setting Final SettingFuel System BatteryCorrection CauseProblem Cause TroubleshootingLoss of Drive Troubleshootingchart ProblemcauseNone Tractor -- Model Number SchematicTractor -- Model Number Electrical Tray 7476041268/-I Tractor -- Model Number 917.273322 Chassis and Enclosures14477 147Description Tractor --MODEL Number Ground Drive 104 \Nut, Crownlock 5/16-18 X2574490548 Bolt Hex Flghd 5/16-18 Gr5 Screw Hex Wsh, Hi-LoTractor -- Model Number Steering Tractor --MODEL Number Steering Tractor -- Model Number Engine 151346 Tank Fuet Rear ElbowTractor --MODEL Number Seat Assembly Decals Tractor -- Model Number\i ¸¸ Tractor --MODEL Number List AssemblyPointer, Height 114 222 105 Tractor Model Number Mower DeckMandrel Bolt. Fin Hex Unc xThdroll Mandrel LHTractor Model Number TRANSAXLE--MODEL Number 222-3010L 164591 Tractor -- Model Number TRANSAXLE--MODEL Number 222-3010L Kohler ENGINE-MODEL Number CV25S, Type Number Cover w NOt0f4 Model Number TractorAIR INTAKE/FILTRATION KEY PartStarting System EN GIN E Controls J OIL PAN/LUBRICATION KEY Part NO. NO.DESCRIPTION Starting System KEY Part NO. NO.DESCRIPTIONCrankshaft Exhaust 24-041-02 DescriptioiSuggested Guide for Sighting Slopes for Safe Operation PartsDirect M
Top Page Image Contents