Craftsman 917.289030 Tools Required for Assembly, To Remove Tractor from Carton Unpack Carton

Page 8

'four new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely_ Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket

wrench

set will

make

assembly

easier.

Standard

wrench

sizes

you need

are

listed

below.

 

 

 

(1)

3/4"wrench

(1)

Pliers

 

(1)

1/2"

wrench

(1)

Utility

knife

(I)Tire pressure gauge

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steer- ing wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1, Remove all accessible loose parts and parts boxes from carton°

2.Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

3, Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower steer- ing shaft.

2.Place tabs of steering boot over tab slots in dash and push down to secure,

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from

steering wheel and slide adapter onto steering shaft extension,

5, Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 5/I6 lock washer, 5/16 hex bolt and tighten se- curely,

7.Snap steering wheel insert into center of steering wheel.

8.Remove protective materials from trac- tor hood and grill

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off ski&

INSTALL SEAT

Adjust seat before tightening adjustment knob,

1.Removeadjustment knob and flatwasher securing seat to cardboard packing and set aside for assembly of seat to trac- tor.

2, Pivot seat upward and remove from the cardboard packing, Remove the card- board packing and discard.

3, Place seat on seat pan so head of shoul- der bolt is positioned over large slotted hole in pan,

4o Push down on seat to engage shoulder

bolt in slot and pull seat towards rear of tractor_

5, Pivotseatand pan forward and assemble adjustment knob and flatwasher loosely. Do not tighten,

8

Image 8
Contents Lawn Tracto Sears Craftsman Help LineCraftsman Limited Warranty TWO Years on Tractor Days on BatteryGeneral Operation III. Children Service Safe Handling of GasolineSlope Operation General Service Specifications 1tlt11111t Adapter Tools Required for Assembly Assemble Extension Shaft and BootInstall Steering Wheel Install SeatLabel Check BatteryTo Roll Tractor OFF Skid Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake System@@@ Know Your Tractor Reverse Operation System ROSHOW to USE Your Tractor to SET Parking Brake To Adjust Mower Cutting HeightStopping Mower Blades Ground DriveMower Towing Carts and Other Attach MentsBefore Starting the Engine Check Engine OIL Level ADD GasolineMowing Tips Schedule MaintenanceBefore Blade Care Blade RemovalBattery To Clean Battery and TerminalsTransaxle Cooling BeltsCleaning Clean AIR ScreenIN-LINEFUEL Filter AIR FilterTractor To Remove Mower Service or AdjustmentsTo Install Mower FRONT-TO-BACK Adjustm ENT To Level Mower HousingSID E-TO-S IDE Adjustment Belt Installation To Replace Mower Blade Drive BeltBelt Removal To Check BrakeFront Wheel TOE-IN!CAMBER Sembly To Adjust Throttle Control CableTo Remove Hood and Grill AS To Adjust Carburetor Preliminary SettingFinal Setting Acceleration TestTractor Fuel SystemEngine OIL CylindersEngine will not turn over Problem CauseCorrection Problem Poor Cut uneven CuttingMower WillEngine dies when tractor is shifted into reverse CausecorrectionSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXGARANTiA Limitada DE Craftsman Page Generales IV. RemolqueDE LA Gasolina Page DEL Hoja de pendiente Llaves Herramientas Necesarias Para EL Montaje Antes DE Remover EL Tractor DELA Corredera Adjunte EL VolanteVerifique LA Bateria Para Hacer Rodar EL TractorLista DE Revision Revision DE LA Presion DE LAS LlantasDA DE Todas LAS Correas @@@ Macho DE LA Palanca DE Levanta Pedal DEL EMBRAGUE/FRENO Se usaComo Usar SU Tractor MientoPara Moverse Hacia Adelante Y HA CIA AtrasPara Parar LAS Cuchillas DE LA Sega Usar EL Sistema DE FuncionamientoPara Operar EN Cerros Para Transpo RtarMotor Arranque CON Tiempo FRO 50 Y Menos Consejos Para SegarImportante Generales Tabla DE LubricacionAntes DE Cada Cuidado DE LA Cuchilla LlantasVirifiiz S1STEMA Presencia Operador Nales Enfriamiento DEL TransejeCorreas LUBRICACI6NBujias Tractor Para Remover LA Segadora Para Instalar LA SegadoraPara Nivelar LA Caja DE LA Sega DoraAjuste DE Lado a Lado Ajuste Desde Adelante Hacia ATR,SIMPULSI6N DE Movimiento DE ImpulsionSegadora Para Adjuntar LOS Cables DE Empalme Para Remover LOS CABLES, Invierta EL OrdenReemplazar LA Bateria Para Cambiar LA Bombilla DE LA LUZ DelanteraPara Ajustar EL Cable DE Control DE LA ACELERACI6N Ajuste PreliminarAjuste Final Prueba DE LA AceleracionAceite DEL Motor OtrosEl motor suena pero noarranca Identificacion DE ProblemasSears Ma corte-disparejo ProblemaVibraci6n excesiva El tractor se port en marcha atr&s Mala descarga del csped ProblemaLas cuchillas Page Page OPERAClON Segura Ea/rs

28903, 917.289031, 917.28903, 917.289030 specifications

The Craftsman 917.289031, 917.289030, 28903, and 917.28903 represent a range of robust lawn mowers designed to deliver exceptional performance for residential lawns. Renowned for their reliability, these models combine user-friendly features with advanced technology, making them ideal for both novice and experienced lawn care enthusiasts.

One of the standout features of these Craftsman mowers is their powerful engines, which typically range between 20 to 24 horsepower. This power enables them to handle various types of grass and terrains, providing an efficient cutting experience. The mowers are equipped with a durable, steel cutting deck that ensures a clean and even cut, contributing to a professionally manicured lawn.

Another key characteristic of the Craftsman 917 series is the presence of the innovative Auto Drive system. This technology allows users to engage the mower without having to constantly push, making it easier to navigate through yards, especially for those with larger lawns. The adjustable speed settings further enhance maneuverability, enabling operators to tailor the pace of the mower to their comfort level and the lawn's requirements.

The cutting height on these models is also adjustable, giving users the flexibility to customize their mowing experience. With heights ranging from 1.5 inches to 4 inches, these mowers cater to different grass types and seasonal conditions, ensuring optimal grass health and appearance.

Safety is paramount in the design of these Craftsman mowers. They come equipped with features such as blade brakes and safety switches that halt blade rotation when the operator leaves the seat. This attention to safety minimizes the risk of accidents during operation.

Maintenance is made simpler with the inclusion of easily accessible components and a user-friendly design. Craftsman has integrated features that allow for quick access to the air filter, spark plug, and oil fill, promoting regular upkeep without the need for specialized tools.

In summary, the Craftsman 917.289031, 917.289030, 28903, and 917.28903 models stand out in the lawn mower market thanks to their powerful engines, advanced Auto Drive technology, adjustable cutting heights, and enhanced safety features. Whether one is tackling a small patch of grass or a sprawling lawn, these mowers provide the versatility and durability needed to achieve impressive results year after year.