Craftsman 917.27207 Brake Operation, Tires, Operator Presence System, Blade Care, Blade Removal

Page 18

TRACTOR

Alwaysobservesafetyruleswhen performinganymaintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble hex bolt, lock washer and flat washer in exact order as shown.

5.Tighten bolt securely (27-35 Ft. Lbs. torque_,.

IMPORTANT: Blade bolt is grade 8 heat treated.

manual).

TIRES

Trailing Edge Up

Mandrel Assembly

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE= To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock

systems are working properly. If your tractor does not function as described,

repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachment clutch control is in the

disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to allow access to blades.

2.Remove hex bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with

trailing edge up towards deck as shown.

Blade Center '_

Hole

Flat Wasber,

Lock

_2._Hex Bolt (Grade)*'-_

*A Grade 8 heat treated bolt can be identified by six lines on the bolt head.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen-

ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will

cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone bal-

ancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded

portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

/

/

5/8

BA'I-rERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with

18 an automotive charger will extend its life.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents ICRRFTSMRN+I Limited 90 DAY Warranty on Battery General Operation II. Slope OperationDo not IV. Service III. ChildrenSafety is Involved 3APACITY Repair AgreementCustomer Responsibilities Steering WheelInsert Before Removingtractor from Skid Attach Steering Wheel Tools Required For AssemblyHowto SET Upyourtractor Check Battery To Removetractor from CartonInstall Seat Install Mulcher Plate ChecklistRlR N H L Knowyourtractor Attachment Clutch Lever UsedParking Brake Lever Locks To USE Throttle Control To Adjust Mower Cutting HeightHowto Useyourtractor To SET Parking Brake To Move Forward and BackwardTo Operate On Rills To Adjust Gauge WheelsTo Operate Mower To TransportADD Gasoline Towing Carts and Other AttachmentsBefore Startingthe Engine Check Engine OIL Level To Start EngineLevel Mower Housing MOWlNGTIPS Mower should be properly leveled forGeneral Recommendations Maintenance ScheduleLubrication Chart Before Each USEOperator Presence System Brake OperationTires Blade CareBelts Clean AIR ScreenClean AIR Intakfjcooling Areas Transaxle CoolingEngine OIL Filter AIR FilterSpark Plugs MufflerCleaning To Install MowerTractor To Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingUnderinflated, you will not properly adjust your mower Raise mower to its highest positionTo Replace Mower Blade Drive Belt Belt InstallationTo Adjust Brake Belt RemovalTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral AdjustmentBattery To Start Engine with a WeakTo Replace Headlight Bulb Replacing BatteryTo Remove Hood and Grill Assembly Interlocks and RelaysSeats in carburetor may result if turned in too tight EngineCable SrPecedetCEngineoil TractorEngine Fuel System CylindersCause Correction Troubleshooting ChartProblem EngineVibration ProblemcauseExcessive Poor cut unevenMower blades will Battery Will NotWhen turning Not rotateSchematic Tractor - Model NumberElectrical 22 4152JBulb Light #1156 27 73510400 Nut Keps Hex 1/4-20 UricTractor - Model Number Chassis and Enclosures 16 x 3/4 Tractor -- Model Number Chassis and Enclosures169830 18 126938X BumperHood150 TRACTOR- Model Number Ground Drive11G 166146682 TransaxleEngine Return BrakeTractor - Model Number Steering Assembly 154427 Tractor - Model Number 917.272070 Steering Assembly139768 Fitting, GreaseBrn/Dbr Guard Spark Arrester170548 Control, Throttle 17720410 1589901700O16 Tractor - Model Number Seat AssemblyBlk 72050412 13/32Decals Wheels & Tires173288 Link Front Tractor - Model Number Lift Assembly1718 163552Tractor --MODEL Number Mower Deck TRACTOR--MODEL Number Mower Deck 41A PEERLESSTRANSAXLE- Model Number 206-545C Cylinder HEAD, Valve and Breatheri Rod, push IGNITION/ELECTRICAL Blower Housing and Bafflesi 12-096o24-S 12-041-02-S Gasket Air Cleaner12-113-53-S Decal Air Cleaner Inches 1 inch = 25.4 mm 12-083-f2-SKk t,J Starting System Crankshaftj Exhaust Kit, fuel Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours

917.27207 specifications

The Craftsman 917.27207 is a versatile and robust lawn mower that combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. This walk-behind mower is designed to tackle various grass types and terrains, ensuring a clean, even cut every time.

One of the standout features of the Craftsman 917.27207 is its powerful engine. Equipped with a dependable 159cc engine, it provides ample power to handle even the thickest grass. The manual start ensures reliability, allowing users to get their mowing tasks done quickly without worrying about battery issues. The engine is designed for fuel efficiency, helping homeowners save on gas while minimizing their environmental footprint.

In addition to its powerful engine, the Craftsman 917.27207 features a 21-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capacity, making it ideal for small to medium-sized lawns. The steel construction adds durability, promising longevity and resilience against wear and tear.

Another key characteristic of the Craftsman 917.27207 is its adjustable cutting heights. With six different height settings, ranging from 1.25 inches to 3.75 inches, users can customize their mowing experience to achieve their desired grass length. This feature is particularly beneficial during different seasons when grass growth varies.

The mower also includes a rear bagger option, making grass collection efficient and hassle-free. The 2-in-1 functionality allows users to choose between mulching and bagging, providing flexibility based on their lawn care preferences. The mulching feature finely chops grass clippings, allowing them to return to the lawn as natural fertilizer, promoting healthier growth.

In terms of ergonomics, the Craftsman 917.27207 is designed with user comfort in mind. The adjustable handle provides customizable height options, ensuring that users can mow comfortably without straining their backs. Lightweight yet sturdy, the mower is easy to maneuver around obstacles and tight corners.

Ultimately, the Craftsman 917.27207 brings together power, performance, and adaptability, making it a solid choice for any DIY lawn care enthusiast. With its impressive features and reliable engineering, keeping lawns looking their best has never been easier.
Top Page Image Contents