Craftsman 917.273638 manual Reposition RmGHT Rear Gauge, To Convert to Bagging or Discharging

Page 8

Knob

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLLTRACTOR OFF SKmD

(See Operation section for mocation

and function of controms)

1.Press lift lever plunger and raise

attachment lift lever to its highest po- sition.

2.Release parking brake by depressing clutch/brake pedal.

3.Place gearshift lever in neutral (N)

position.

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKmD

(See Operation section for mocation

and function of controms)

_LWARNmNG: Before starting, read, un- derstand and follow all instructions in the

Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Sit on seat in operating position,

depress clutch/brake pedal and set the

parking brake.

4.Place gear shift lever in neutral (N) position.

5.Press lift lever plunger and raise

attachment lift lever to its highest posi- tion.

6.Start the engine. After engine has started, move throttle control to idle position.

7.Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

8.Slowly release clutch/brake pedal and slowly drive tractor off skid.

9.Apply brake to stop tractor, set park- ing brake and place gearshift lever in neutral position.

10.Turn ignition key to "STOP" position. Continue with the instructions that follow.

REPOSITION RmGHT REAR GAUGE

For shipping purposes, the right rear gauge wheel assembly is mounted upside down on the mower. Remove the gauge wheel assembly and reinstall from the bottom as shown. To adjust gauge wheels, see the Operation section in this manual.

mNSTALL MULCHER PLATE

(If previousmy removed}

1.Raise and hold deflector shield in up- right position.

2.Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

3.Nook front latch into hole on front of mower deck.

4.Nook rear latch into hole on back of mower deck.

_I_CAUTION: Do not remove deflector shield from mower.

Deflector

Shield

Mulcher

Plate

Latch

Hooks

TO CONVERT TO BAGGING OR DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are designed

8 for discharging and bagging also.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Craftsmiin Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL Limitedwarrantyon CraftsmanridingequipmentLimitedwarrantyon Battery Slope Operation Taft grass can hide obstacles Do notPage IAPFSG-SL RC12YCPSI U1RCheck Battery Adjust SeatHOW To SET UP Your Tractor Reposition RmGHT Rear Gauge To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessALL Belts Check Brake System@@@@ Know Your Tractor STOPPmNG To Adjust Gauge Wheels To TransportTo Operate Mower To Operate on HillsTo Start Engine Before Starting the Engine Check Engine OIL LevelADD Gasoline 00272 Ervcdates Before Each USEBattery TractorOperator Presence System Blade CareTo Clean Batteryandterminals To ChangeengineoilTransaxle Cooling AIR FilterMuffler Spark PlugsTRACTO£ To Reiiovemower SIDE-TO-SIDE Adjustment with Bubble Level Alternate SIDE-TO-SIDE Adjustment MethodBelt Installation To Check and Adjust BrakeTo Adjust Brake Both Front Links Must be Equalin LengthTransaxle Gear Shift Lever NEU- Tral Adjustment MentFront Wheel TOE=IN/CAMBER To Remove Wheel for RepairsTery To AttachjumpercablesTo REMOVECABLES,REVERSE Order To Remove Hood and Grill AS- SemblyTo Adjust Carburetor Preliminary SettingFinal Setting Acceleration TestFuel System Engne OILCause CORRECTmON Engine ContinuesTo run when Operator Leaves Seat With attach Ment Clutch EngagedProblem Cause Battery wiii not chargeCORRECTmON Mower blades wiii Remove Obstruction Not rotatePage Tractor - Model Number Schematic DiodeTractor - Model Number ElectricalTractor o o Model Number KEY PartTractor Model Number 917.273638 CHASSmSAND Enclosures Tractor ooMODEL Number 917.273638 CHASSmSAND Enclosures Tractor - Model Number Ground Drive KEY Part STEERmNG Tractor o o Model Number Tractor Model Number Optional EquipmentKEY Part NO. NO.DESCRIPTION Description Tractor Model Number Seat AssemblyKEY Decals KEY Part DescriptionTractor - Model Number Tractor ooMODEL Number LmFTASSEMBLY Mower Deck KEY Part DANATRANSAXLE==MODELNUMBERD4360=180 Tractor o o Model Number Dana TRANSAXLE-MODEL Number D4360ol 144I 947 Intake 267 695134 Screw Casing Clamp 691279 505 691251 Nut Governor Control Lever 1005 699043 Page Suggested Guide for Sighting Slopes for Safe Operation Iiiiiiiiiiiiiiiiiiii CanadaIiiiiiiiiiiiiiiiiii Rev 7.2.04 MH
Top Page Image Contents