Craftsman 917.273638 manual Tery, To Attachjumpercables, To REMOVECABLES,REVERSE Order

Page 24

TO STARTENGINEWiTH A WEAK BAT-

TERY

,_kWARNmNG:Lead-acidbatteriesgen- erate explosivegases. Keepsparks,flame andsmoking materialsawayfrom bat-

teries. Alwayswear eye protectionwhen around batteries.

If your batteryis too weakto start the engine, it should be recharged.(See "BAT- TERY" in the MAINTENANCEsectionof

this manual).

If "jumpercables"are usedfor emergency starting, followthis procedure: IMPORTANT:Yourtractor isequipped with a 12 volt system.The other vehicle must also be a 12 volt system.Do not use your tractorbatteryto start othervehicles.

TO ATTACHJUMPERCABLES-

1.Connectone end of the REDcable

to the POSITIVE(+) terminal of each battery(A-B),takingcare not to short againsttractor chassis.

2.Connectone end of the BLACKcable to the NEGATIVE(-) terminal (C)of fully charged battery.

3.Connectthe other end of the BLACK cable(D) to goodchassisground, awayfrom fuel tank and battery.

TO REMOVECABLES,REVERSE ORDER-

1.BLACKcablefirst from chassis and then from the fully charged battery.

2.RED cablelast from both batteries.

DD

02614

Weak or Dead Fully Charged

BatteryBattery

REPLACING BATTERY

n_asWARNmNG: Do not short battery termi-

by allowing a wrench or any other object to contact both terminals at the same time.

Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected

first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

mex

BoUt

Positive (Red)

CabUe

Negative (BUack)

CaMe

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

mNTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

,_ Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Connector

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Craftsmiin Limitedwarrantyon Craftsmanridingequipment Limitedwarrantyon BatterySears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL Slope Operation Taft grass can hide obstacles Do notPage IAPFSG-SL RC12YCPSI U1RAdjust Seat HOW To SET UP Your TractorCheck Battery Reposition RmGHT Rear Gauge To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessALL Belts Check Brake System@@@@ Know Your Tractor STOPPmNG To Adjust Gauge Wheels To TransportTo Operate Mower To Operate on HillsBefore Starting the Engine Check Engine OIL Level ADD GasolineTo Start Engine 00272 Ervcdates Before Each USEBattery TractorOperator Presence System Blade CareTo Clean Batteryandterminals To ChangeengineoilTransaxle Cooling AIR FilterMuffler Spark PlugsTRACTO£ To Reiiovemower SIDE-TO-SIDE Adjustment with Bubble Level Alternate SIDE-TO-SIDE Adjustment MethodBelt Installation To Check and Adjust BrakeTo Adjust Brake Both Front Links Must be Equalin LengthTransaxle Gear Shift Lever NEU- Tral Adjustment MentFront Wheel TOE=IN/CAMBER To Remove Wheel for RepairsTery To AttachjumpercablesTo REMOVECABLES,REVERSE Order To Remove Hood and Grill AS- SemblyTo Adjust Carburetor Preliminary SettingFinal Setting Acceleration TestFuel System Engne OILCause CORRECTmON Engine ContinuesTo run when Operator Leaves Seat With attach Ment Clutch EngagedProblem Cause Battery wiii not chargeCORRECTmON Mower blades wiii Remove Obstruction Not rotatePage Tractor - Model Number Schematic DiodeTractor - Model Number ElectricalTractor o o Model Number KEY PartTractor Model Number 917.273638 CHASSmSAND Enclosures Tractor ooMODEL Number 917.273638 CHASSmSAND Enclosures Tractor - Model Number Ground Drive KEY Part STEERmNG Tractor o o Model Number Tractor Model Number Optional EquipmentKEY Part NO. NO.DESCRIPTION Tractor Model Number Seat Assembly KEYDescription Decals KEY Part DescriptionTractor - Model Number Tractor ooMODEL Number LmFTASSEMBLY Mower Deck KEY Part DANATRANSAXLE==MODELNUMBERD4360=180 Tractor o o Model Number Dana TRANSAXLE-MODEL Number D4360ol 144I 947 Intake 267 695134 Screw Casing Clamp 691279 505 691251 Nut Governor Control Lever 1005 699043 Page Suggested Guide for Sighting Slopes for Safe Operation Iiiiiiiiiiiiiiiiiiii CanadaIiiiiiiiiiiiiiiiiii Rev 7.2.04 MH
Top Page Image Contents