Craftsman 917.273638 manual 00272

Page 15

COLD WEATHER STARTING ( 50 ° F and below)

6.When engine starts, leave throttle control in choke position until engine warms up and begins to run roughly. Once rough running begins, imme- diately move the throttle control to the

fast position. Engine warm-up may take from several seconds to several

minutes (the colder the temperature,

the longer the warm-up).

The attachments can also be used dur- ing the engine warm-up period.

NOTE: If at a high altitude (above 3000

feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance

(see "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual).

MOWmNG TIPS

Mower should be properly leveled for

best mowing performance. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has already been

cut. Have the cut area to the right of the tractor. This will result in a more

even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished.

f

J

J

00272

If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings.

Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the at- tachment being used.

MULCHmNG MOWmNG TIPS

mMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean after each use.

The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recut- ting action of the blades.

Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, the newly cut area will not be exposed to direct sunlight.

o For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re- duce your width of cut on each pass and mow slowly.

MAX 1/3

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec-

ond cut, mow across (perpendicular) to the first cut path.

Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This will help prevent matting and graining of the lawn.

15

Image 15
Contents Craftsmiin Limitedwarrantyon Craftsmanridingequipment Limitedwarrantyon BatterySears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL Slope Operation Do not Taft grass can hide obstaclesPage U1R IAPFSG-SLRC12YC PSIAdjust Seat HOW To SET UP Your TractorCheck Battery To Convert to Bagging or Discharging Reposition RmGHT Rear GaugeCheck Brake System Check Tire PressureCheck Deck Levelness ALL Belts@@@@ Know Your Tractor STOPPmNG To Operate on Hills To Adjust Gauge WheelsTo Transport To Operate MowerBefore Starting the Engine Check Engine OIL Level ADD GasolineTo Start Engine 00272 Before Each USE ErvcdatesBlade Care BatteryTractor Operator Presence SystemAIR Filter To Clean BatteryandterminalsTo Changeengineoil Transaxle CoolingSpark Plugs MufflerTRACTO£ To Reiiovemower Alternate SIDE-TO-SIDE Adjustment Method SIDE-TO-SIDE Adjustment with Bubble LevelBoth Front Links Must be Equalin Length Belt InstallationTo Check and Adjust Brake To Adjust BrakeTo Remove Wheel for Repairs Transaxle Gear Shift Lever NEU- Tral AdjustmentMent Front Wheel TOE=IN/CAMBERTo Remove Hood and Grill AS- Sembly TeryTo Attachjumpercables To REMOVECABLES,REVERSE OrderAcceleration Test To Adjust CarburetorPreliminary Setting Final SettingEngne OIL Fuel SystemCause Operator Leaves Seat With attach Ment Clutch Engaged CORRECTmONEngine Continues To run whenRemove Obstruction Not rotate Problem CauseBattery wiii not charge CORRECTmON Mower blades wiiiPage Diode Tractor - Model Number SchematicElectrical Tractor - Model NumberKEY Part Tractor o o Model NumberTractor Model Number 917.273638 CHASSmSAND Enclosures Tractor ooMODEL Number 917.273638 CHASSmSAND Enclosures Tractor - Model Number Ground Drive KEY Part STEERmNG Tractor o o Model Number Optional Equipment Tractor Model NumberKEY Part NO. NO.DESCRIPTION Tractor Model Number Seat Assembly KEYDescription KEY Part Description DecalsTractor - Model Number Tractor ooMODEL Number LmFTASSEMBLY Mower Deck KEY Part DANATRANSAXLE==MODELNUMBERD4360=180 Tractor o o Model Number Dana TRANSAXLE-MODEL Number D4360ol 144I 947 Intake 267 695134 Screw Casing Clamp 691279 505 691251 Nut Governor Control Lever 1005 699043 Page Suggested Guide for Sighting Slopes for Safe Operation Rev 7.2.04 MH IiiiiiiiiiiiiiiiiiiiCanada Iiiiiiiiiiiiiiiiiii